FireCADCalc

Thermal Stress and Force in a Restrained Bar or Pipe

Axial thermal stress and end force in a bar or pipe that is fully restrained while heated or cooled, and the free expansion it would have had.

Inputs

Examples: Steel bar 5 000 mm², heated 100 K, 10 mStainless pipe 3 000 mm², 150 K, 6 mAluminium busbar 1 200 mm², cooled 40 K, 4 m

Optional: the page warns when the thermal stress exceeds it.

Results

Sign: compression is positive (heating) and tension negative (cooling), the reverse of the tension-positive convention.

Rigid restraints and elastic behaviour; real anchors and supports yield a little, and a long slender member may buckle before reaching this stress.

Thermal stress E α ΔT (positive = compressive, from heating; negative = tensile, from cooling)500.83MPa
Force on the restraints1,502.5kN
Free thermal expansion if unrestrained15.570mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Steel bar 5 000 mm², heated 100 K, 10 m. The inputs, in the units selected above:

InputValue
Young's modulus200.00 GPa
Mean coefficient of thermal expansion12.000 µm/(m·K)
Temperature change100.00 K
Cross-section area of the metal5,000.0 mm²
Length between restraints10.000 m
Yield strength at temperature (0 = not checked)0 MPa

Applying the formula below gives:

ResultValue
Thermal stress E α ΔT (positive = compressive, from heating; negative = tensile, from cooling)240.00 MPa
Force on the restraints1,200.0 kN
Free thermal expansion if unrestrained12.000 mm

Open this example in the calculator and change any input.

Formula

\(\sigma = E\, \alpha\, \Delta T\)

\(F = \sigma A\)

\(\delta = \alpha\, \Delta T\, L\)

Variables

Symbol Meaning SI unit
\(E\) Young's modulus Pa
\(\alpha\) coefficient of thermal expansion 1/K
\(\Delta T\) temperature change K
\(A\) metal cross-section m²
\(L\) length m
\(S_y\) yield strength at temperature (optional check) Pa
\(\sigma\) thermal stress, positive in compression (heating) Pa
\(F\) force on the restraints N
\(\delta\) free expansion m

Method and standards

A member prevented from expanding carries the strain it would have had, α ΔT, as elastic strain: stress is E α ΔT, independent of length.

Where it is used

  • Estimating anchor loads on straight pipe runs.
  • Checking busbars, rails and frames for temperature changes.
  • Explaining why expansion loops are needed.

Common mistakes

  • Using α at room temperature for hot service (it rises with temperature).
  • Forgetting the anchors and supports are not rigid.
  • Ignoring buckling of slender members.

Assumptions and limits

  • Fully rigid restraints; elastic material; uniform temperature.
  • Sign: σ is positive in compression (heating) and negative in tension (cooling).
  • Elastic only: if σ exceeds the yield strength (enter it to be warned), the member yields. Buckling of slender members is not checked.

References

  • σ = E α ΔT

Questions and answers

What stress does heating a restrained steel bar by 100 K cause?

About 240 MPa (200 GPa × 12×10⁻⁶ × 100): close to yield for mild steel, which is why pipes need expansion loops.

What force acts on the anchors?

Stress times metal area: 1.2 MN for 5 000 mm² in the example.

What if it is free to expand?

It grows α ΔT L, 12 mm over 10 m in the example, and has no thermal stress.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.