FireCADCalc

Principal Stresses and Mohr's Circle (2D)

Principal stresses, maximum in-plane shear stress and the principal angle for a plane stress state from σx, σy and τxy, as on Mohr's circle.

Inputs

Examples: σx 80, σy −40, τ 30 MPaPure shear 50 MPaσx 100, σy 60, τ −20 MPa

Results

Plane stress; tension positive. Absolute maximum shear including the out-of-plane principal stress (zero): 50 MPa, larger than the in-plane value when σ₁ and σ₂ have the same sign.

Major principal stress50.000MPa
Minor principal stress-50.000MPa
Maximum in-plane shear stress (circle radius)50.000MPa
Centre of the circle (σx + σy)/20MPa
Angle from x to the major principal axis45.000°

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: σx 80, σy −40, τ 30 MPa. The inputs, in the units selected above:

InputValue
Normal stress in x80.000 MPa
Normal stress in y-40.000 MPa
Shear stress30.000 MPa

Applying the formula below gives:

ResultValue
Major principal stress87.082 MPa
Minor principal stress-47.082 MPa
Maximum in-plane shear stress (circle radius)67.082 MPa
Centre of the circle (σx + σy)/220.000 MPa
Angle from x to the major principal axis13.283 °

Open this example in the calculator and change any input.

Formula

\(\sigma_{1,2} = \frac{\sigma_x + \sigma_y}{2} \pm \sqrt{\left(\frac{\sigma_x - \sigma_y}{2}\right)^2 + \tau_{xy}^2}, \quad \tan 2\theta_p = \frac{2\tau_{xy}}{\sigma_x - \sigma_y}\)

Variables

Symbol Meaning SI unit
\(\sigma_x\) Normal stress in x Pa
\(\sigma_y\) Normal stress in y Pa
\(\tau_{xy}\) Shear stress Pa
\(\sigma_1\) Major principal stress Pa
\(\sigma_2\) Minor principal stress Pa
\(\tau_{max}\) Maximum in-plane shear stress (circle radius) Pa
\(\sigma_c\) Centre of the circle (σx + σy)/2 Pa
\(\theta_p\) Angle from x to the major principal axis rad

Method and standards

Stress transformation.

Where it is used

  • Combined loading checks.
  • Strength of materials examinations.

Common mistakes

  • Sign convention for shear.
  • Forgetting the third principal stress.

Assumptions and limits

  • Plane stress. The absolute maximum shear max(|σ₁|, |σ₂|, |σ₁ − σ₂|)/2 (third principal stress zero) is given in a note.

References

  • Textbook mechanics (stress transformation, Mohr 1882)

Questions and answers

σx 80, σy −40, τ 30 MPa?

σ₁ 87.1, σ₂ -47.1 MPa; τ_max 67.1 MPa.

Which way is θ_p?

Counter-clockwise from x, with positive τ_xy acting up on the x-face.

Why principal stresses?

Failure theories compare them with the material's strength.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.