FireCADCalc

Eccentrically Loaded Column (Secant Formula)

Maximum compressive stress in a column with an eccentric axial load by the secant formula, from load, eccentricity, section and effective length.

Inputs

Examples: 100 kN at 10 mm on a 150 mm section, 3 mPipe strut: 50 kN at 5 mm, 1 500 mm², k 30 mm, c 44 mm, 4 mNo eccentricity: 200 kN

Results

Eccentricity ratio0.43548
Secant argument0.47058
Maximum compressive stress52.231MPa
Direct stress35.088MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 100 kN at 10 mm on a 150 mm section, 3 m. The inputs, in the units selected above:

InputValue
Axial load100.00 kN
Eccentricity of the load10.000 mm
Cross-sectional area2,850.0 mm²
Radius of gyration about the bending axis41.500 mm
Distance from the axis to the extreme fibre75.000 mm
Effective length3.0000 m
Young's modulus207.00 GPa

Applying the formula below gives:

ResultValue
Eccentricity ratio0.43548
Secant argument0.47058
Maximum compressive stress52.231 MPa
Direct stress35.088 MPa

Open this example in the calculator and change any input.

Formula

\(\sigma_{max} = \frac{P}{A}\left[1 + \frac{e c}{k^2} \sec\left(\frac{L_e}{2k}\sqrt{\frac{P}{AE}}\right)\right]\)

Variables

Symbol Meaning SI unit
\(P\) Axial load N
\(e\) Eccentricity of the load m
\(A\) Cross-sectional area m²
\(k\) Radius of gyration about the bending axis m
\(c\) Distance from the axis to the extreme fibre m
\(L_e\) Effective length m
\(E\) Young's modulus Pa
\(ec/k^2\) Eccentricity ratio -
\(\frac{L_e}{2k}\sqrt{\frac{P}{AE}}\) Secant argument -
\(\sigma_{max}\) Maximum compressive stress Pa
\(P/A\) Direct stress Pa

Method and standards

Elastic bending of a column with eccentric load.

Where it is used

  • Brackets and offset-loaded columns.
  • Strength of materials examinations.

Common mistakes

  • Wrong bending axis.
  • Ignoring accidental eccentricity.

Assumptions and limits

  • Elastic, pin-ended effective length.
  • σ_max is not compared with the yield strength and no factor of safety is applied: check σ_max against your allowable, or solve for the load that makes it reach yield divided by the factor.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 4 (secant column formula)

Questions and answers

Why does eccentricity matter so much?

The bending moment grows as the column bows, through the secant term.

What if there is no eccentricity?

The stress is P/A until buckling.

How is it used in design?

Find the load that makes σ_max equal yield, then apply a factor of safety.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.