FireCADCalc

Curved Beam Bending Stress (Winkler–Bach), Rectangular Section

Neutral axis shift and bending stresses at the inner and outer fibres of a curved beam of rectangular section, as in hooks and C-frames, by the Winkler–Bach theory.

Inputs

Examples: Hook-like: ri 50, h 40, b 20 mm, closing 1.5 kN·mC-frame: ri 100, h 80, b 30 mm, opening 4 kN·mTight ring: ri 10, h 20, b 10 mm, 100 N·m

Results

Sign: a positive moment straightens the beam (tension at the inner fibre). In a crane hook the direct tension P/A is added.

Radius of the centroid20.000mm
Radius of the neutral axis h/ln(r_o/r_i)18.205mm
Neutral axis shift r_c − r_n1.7952mm
Stress at the inner fibre228.52MPa
Stress at the outer fibre-109.51MPa
Straight-beam stress 6M/(b h²) for comparison150.00MPa

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hook-like: ri 50, h 40, b 20 mm, closing 1.5 kN·m. The inputs, in the units selected above:

InputValue
Inner radius50.000 mm
Section depth (radial)40.000 mm
Section width20.000 mm
Bending moment (positive straightens the beam)-1,500.0 N·m

Applying the formula below gives:

ResultValue
Radius of the centroid70.000 mm
Radius of the neutral axis h/ln(r_o/r_i)68.052 mm
Neutral axis shift r_c − r_n1.9481 mm
Stress at the inner fibre-347.49 MPa
Stress at the outer fibre234.72 MPa
Straight-beam stress 6M/(b h²) for comparison281.25 MPa

Open this example in the calculator and change any input.

Formula

\(r_n = \frac{h}{\ln(r_o/r_i)}, \quad e = r_c - r_n, \quad \sigma_i = \frac{M(r_n - r_i)}{A e r_i}, \quad \sigma_o = \frac{M(r_n - r_o)}{A e r_o}\)

Variables

Symbol Meaning SI unit
\(r_i\) Inner radius m
\(h\) Section depth (radial) m
\(b\) Section width m
\(M\) Bending moment (positive straightens the beam) N·m
\(r_c\) Radius of the centroid m
\(r_n\) Radius of the neutral axis h/ln(r_o/r_i) m
\(e\) Neutral axis shift r_c − r_n m
\(\sigma_i\) Stress at the inner fibre Pa
\(\sigma_o\) Stress at the outer fibre Pa
\(\sigma_{straight}\) Straight-beam stress 6M/(b h²) for comparison Pa

Method and standards

Winkler–Bach curved beam theory.

Where it is used

  • Hooks, clamps, C-frames and press frames.
  • Strength of materials examinations.

Common mistakes

  • Using the straight-beam formula.
  • Rounding e (a small difference of large numbers).

Assumptions and limits

  • Rectangular section, elastic.
  • For large radius-to-depth ratios the shift e is found from the series of ln(r_o/r_i), avoiding the loss of digits in r_c − r_n.
  • Bending only: in a crane hook add the direct stress P/A to both fibres.

References

  • Shigley's Mechanical Engineering Design (Budynas and Nisbett)
  • ch. 3 (curved beams in bending, rectangular section r_n = h / ln(r_o/r_i))

Questions and answers

Why is the inner fibre stress higher?

The neutral axis shifts towards the centre of curvature, and the inner fibres are shorter.

How much higher?

For r_i = 50 mm and h = 40 mm, about 24 % above the straight-beam value.

When can curvature be ignored?

When the radius is large compared with the depth (r_c/h above about 10).

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.