FireCADCalc

Combined Bending and Torsion of a Shaft

Equivalent twisting and bending moments and the maximum shear and normal stresses in a solid round shaft under bending and torsion (Guest and Rankine).

Inputs

Examples: 1.2 kN·m and 1.6 kN·m on 60 mmBending only 500 N·m on 40 mmTorque only 3 kN·m on 70 mm

Results

Static loads; shock and fatigue factors (as in the ASME shaft code) multiply M and T before combining.

Equivalent twisting moment √(M² + T²)500.00N·m
Equivalent bending moment (M + T_e)/2500.00N·m
Maximum shear stress 16 T_e/(π d³)39.789MPa
Maximum normal stress 32 M_e/(π d³)79.577MPa
Diameter for the allowable shear stress39.929mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1.2 kN·m and 1.6 kN·m on 60 mm. The inputs, in the units selected above:

InputValue
Bending moment1,200.0 N·m
Twisting moment (torque)1,600.0 N·m
Shaft diameter60.000 mm
Allowable shear stress (to size the shaft)50.000 MPa

Applying the formula below gives:

ResultValue
Equivalent twisting moment √(M² + T²)2,000.0 N·m
Equivalent bending moment (M + T_e)/21,600.0 N·m
Maximum shear stress 16 T_e/(π d³)47.157 MPa
Maximum normal stress 32 M_e/(π d³)75.451 MPa
Diameter for the allowable shear stress58.841 mm

Open this example in the calculator and change any input.

Formula

\(T_e = \sqrt{M^2 + T^2}, \quad M_e = \tfrac12 (M + T_e), \quad \tau_{max} = \frac{16 T_e}{\pi d^3}, \quad \sigma_{max} = \frac{32 M_e}{\pi d^3}\)

Variables

Symbol Meaning SI unit
\(M\) Bending moment N·m
\(T\) Twisting moment (torque) N·m
\(d\) Shaft diameter m
\(\tau_a\) Allowable shear stress (to size the shaft) Pa
\(T_e\) Equivalent twisting moment √(M² + T²) N·m
\(M_e\) Equivalent bending moment (M + T_e)/2 N·m
\(\tau_{max}\) Maximum shear stress 16 T_e/(π d³) Pa
\(\sigma_{max}\) Maximum normal stress 32 M_e/(π d³) Pa
\(d_{min}\) Diameter for the allowable shear stress m

Method and standards

Principal stresses at the shaft surface.

Where it is used

  • Line shafts and spindles.
  • Machine design examinations.

Common mistakes

  • Adding M and T directly.
  • Forgetting shock factors.

Assumptions and limits

  • Solid round shaft, static. Shock and fatigue factors (K_m, K_t), keyways and other stress raisers are not applied: multiply M and T by your factors before entering them.
  • d_min sizes the shaft by the maximum shear stress (Guest) only; check σ_max against the allowable normal stress (Rankine) as well.

References

  • Textbook mechanics (Guest's maximum shear stress and Rankine's maximum normal stress theories)

Questions and answers

1.2 kN·m bending and 1.6 kN·m torque on a 60 mm shaft?

T_e = 2 kN·m: shear 47.2 MPa; normal 75.5 MPa.

What diameter for 50 MPa shear?

58.8 mm.

Which theory for ductile shafts?

Maximum shear (Guest) or distortion energy; Rankine suits brittle materials.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.