FireCADCalc

Cantilever Beam: Moment, Deflection, Stress

Fixed-end reaction and moment, tip deflection and bending stress of a cantilever under a uniform load and a point load at the free end.

Inputs

Examples: 2 m bracket, 2 kN/m + 5 kN, I 1 943 cm⁴, Z 194 cm³1.2 m, end load 10 kN only, I 5 000 cm⁴, Z 400 cm³Aluminium 0.5 m, 0.5 kN/m + 0.2 kN, E 70 GPa, I 50 cm⁴, Z 10 cm³

Results

Fully fixed support assumed; a real support that rotates adds deflection. Check shear and buckling separately.

Bending moment at the fixed end0.16250kN·m
Tip deflection0.34970mm
Maximum bending stress16.250MPa
Reaction at the fixed end0.45000kN
Length over deflection1,429.8

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 2 m bracket, 2 kN/m + 5 kN, I 1 943 cm⁴, Z 194 cm³. The inputs, in the units selected above:

InputValue
Length from the fixed end2.0000 m
Uniformly distributed load (including self weight)2.0000 kN/m
Point load at the free end5.0000 kN
Modulus of elasticity200.00 GPa
Second moment of area1,943.0 cm⁴
Elastic section modulus194.00 cm³

Applying the formula below gives:

ResultValue
Bending moment at the fixed end14.000 kN·m
Tip deflection4.4605 mm
Maximum bending stress72.165 MPa
Reaction at the fixed end9.0000 kN
Length over deflection448.38

Open this example in the calculator and change any input.

Formula

\(R = wL + P \qquad M_{max} = \frac{wL^2}{2} + PL \qquad \delta_{max} = \frac{wL^4}{8EI} + \frac{PL^3}{3EI} \qquad \sigma_b = \frac{M_{max}}{Z}\)

Variables

Symbol Meaning SI unit
\(L\) length m
\(w\) distributed load N/m
\(P\) tip load N
\(E\) modulus of elasticity Pa
\(I\) second moment of area m⁴
\(Z\) section modulus m³
\(M_{max}\) fixed-end moment N·m
\(\delta_{max}\) tip deflection m
\(\sigma_b\) bending stress Pa
\(R\) fixed-end reaction N
\(L/\delta\) length over deflection –

Method and standards

Euler–Bernoulli small-deflection theory for a cantilever, superposing the two load cases.

Where it is used

  • Pipe support brackets.
  • Platform and walkway brackets.
  • Davit and lifting arms (with factors).

Common mistakes

  • Assuming a bolted end plate is fully fixed.
  • Leaving out self weight.
  • Mixing units of I and Z.

Assumptions and limits

  • Linear elastic; fully fixed support.
  • The stress is not compared with an allowable. I and Z are entered separately: take both from the same section, as an inconsistent pair is not detected.

References

  • Euler–Bernoulli beam theory

Questions and answers

What does a 2 m bracket with 2 kN/m and 5 kN at the tip do?

14 kN·m at the wall, 4.46 mm tip deflection and 72 MPa with I 1943 cm⁴, Z 194 cm³.

Why is the tip deflection so sensitive to length?

It grows with the cube (point load) or fourth power (uniform load) of length.

Is the support really fixed?

Rarely fully; a support that rotates adds deflection.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.