FireCADCalc

Chromium and Nickel Equivalents (Schaeffler and WRC-1992)

Chromium and nickel equivalents of stainless weld metal by the Schaeffler and WRC-1992 formulas, the Cr/Ni ratio and the solidification mode.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 308L-type deposit310-type fully austenitic

Results

Modes from the WRC-1992 ratio: A (fully austenitic, below 1.25) and AF risk hot cracking; FA (1.48–1.95) with a few per cent ferrite is the usual target for 308L/316L welds. Read ferrite number from the WRC-1992 diagram itself.

Schaeffler Cr equivalent26.350
Schaeffler Ni equivalent24.900
WRC-1992 Cr equivalent25.600
WRC-1992 Ni equivalent25.325
WRC-1992 ratio1.0109
Solidification mode (0 A, 1 AF, 2 FA, 3 F)0

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 308L-type deposit. The inputs, in the units selected above:

InputValue
Chromium (wt %)19.500 %
Molybdenum (wt %)0.20000 %
Silicon (wt %)0.40000 %
Niobium (wt %)0 %
Nickel (wt %)10.000 %
Carbon (wt %)0.020000 %
Manganese (wt %)1.8000 %
Nitrogen (wt %)0.050000 %
Copper (wt %)0.10000 %

Applying the formula below gives:

ResultValue
Schaeffler Cr equivalent20.300
Schaeffler Ni equivalent11.500
WRC-1992 Cr equivalent19.700
WRC-1992 Ni equivalent11.725
WRC-1992 ratio1.6802
Solidification mode (0 A, 1 AF, 2 FA, 3 F)2.0000

Open this example in the calculator and change any input.

Formula

\(Cr_{eq} = Cr + Mo + 0.7Nb,\quad Ni_{eq} = Ni + 35C + 20N + 0.25Cu\ (\text{WRC-1992})\)

\(Cr_{eq} = Cr + Mo + 1.5Si + 0.5Nb,\quad Ni_{eq} = Ni + 30C + 0.5Mn\ (\text{Schaeffler})\)

Variables

Symbol Meaning SI unit
\(Cr\) Chromium (wt %) -
\(Mo\) Molybdenum (wt %) -
\(Si\) Silicon (wt %) -
\(Nb\) Niobium (wt %) -
\(Ni\) Nickel (wt %) -
\(C\) Carbon (wt %) -
\(Mn\) Manganese (wt %) -
\(N\) Nitrogen (wt %) -
\(Cu\) Copper (wt %) -
\(Cr_{eq,S}\) Schaeffler Cr equivalent -
\(Ni_{eq,S}\) Schaeffler Ni equivalent -
\(Cr_{eq,WRC}\) WRC-1992 Cr equivalent -
\(Ni_{eq,WRC}\) WRC-1992 Ni equivalent -
\(Cr_{eq}/Ni_{eq}\) WRC-1992 ratio -
\(\text{mode}\) Solidification mode (0 A, 1 AF, 2 FA, 3 F) -

Method and standards

Equivalent formulas.

Where it is used

  • Dissimilar welds (stainless to carbon steel).
  • Filler selection for austenitic stainless.

Common mistakes

  • Ignoring dilution from the base metal.
  • Using Schaeffler for high-nitrogen alloys.

Assumptions and limits

  • Weld metal compositions. The ferrite number is not computed: read it from the WRC-1992 diagram. The Schaeffler Ni equivalent leaves out nitrogen, so for high-nitrogen fillers the two methods can disagree.

References

  • Schaeffler (1949) and WRC-1992 (Kotecki and Siewert) equivalent formulas; solidification-mode ratios from Lippold and Kotecki
  • Welding Metallurgy and Weldability of Stainless Steels (Wiley, 2005)

Questions and answers

Why does ferrite matter in stainless welds?

A little ferrite (3–10 FN) during solidification absorbs sulphur and phosphorus and prevents hot cracking.

Why two formulas?

Schaeffler is the classic diagram; WRC-1992 adds nitrogen and copper and predicts ferrite better for modern fillers.

What do the defaults represent?

A 308L-type weld deposit.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.