FireCADCalc

Steinhart–Hart Coefficients from Three Points

Steinhart–Hart coefficients A, B and C of a thermistor from three resistance–temperature points, and the temperature at a measured resistance.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 10 k NTC: 0, 25, 50 °C points; 5 kΩWide range −20, 40, 120 °CThree close points 20, 30, 40 °C

Calibration points

Results

Pick points spread over the range of use; the fit is exact at the three points.

Coefficient A0.001125
Coefficient B2.3472e-04
Coefficient C8.5631e-08
Temperature at the measured resistance41.580°C

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 10 k NTC: 0, 25, 50 °C points; 5 kΩ. The inputs, in the units selected above:

InputValue
Temperature 10 °C
Resistance at T₁32,650 Ω
Temperature 225.000 °C
Resistance at T₂10,000 Ω
Temperature 350.000 °C
Resistance at T₃3,603.0 Ω
Measured resistance5,000.0 Ω

Applying the formula below gives:

ResultValue
Coefficient A0.001125
Coefficient B2.3472e-04
Coefficient C8.5631e-08
Temperature at the measured resistance41.580 °C

Open this example in the calculator and change any input.

Formula

\(\frac1T = A + B \ln R + C (\ln R)^3\)

With \(L_i = \ln R_i\), \(Y_i = 1/T_i\) and \(\gamma_2 = \frac{Y_2 - Y_1}{L_2 - L_1}\), \(\gamma_3 = \frac{Y_3 - Y_1}{L_3 - L_1}\):

\(C = \frac{\gamma_3 - \gamma_2}{(L_3 - L_2)(L_1 + L_2 + L_3)}, \quad B = \gamma_2 - C\left(L_1^2 + L_1L_2 + L_2^2\right), \quad A = Y_1 - \left(B + C L_1^2\right)L_1\)

Variables

Symbol Meaning SI unit
\(T_1\) Temperature 1 K
\(R_1\) Resistance at T₁ Ω
\(T_2\) Temperature 2 K
\(R_2\) Resistance at T₂ Ω
\(T_3\) Temperature 3 K
\(R_3\) Resistance at T₃ Ω
\(R_m\) Measured resistance Ω
\(A\) Coefficient A -
\(B\) Coefficient B -
\(C\) Coefficient C -
\(T\) Temperature at the measured resistance K
\(R\) Resistance in the equation Ω
\(L_i, Y_i\) ln R_i (R in Ω) and 1/T_i -, 1/K
\(\gamma_2, \gamma_3\) Slopes between points 1–2 and 1–3 K⁻¹

Method and standards

Three linear equations in A, B and C.

Where it is used

  • Thermistor calibration.
  • Programming instruments with ABC coefficients.

Common mistakes

  • Points too close together.
  • Mixing °C and K.

Assumptions and limits

  • NTC thermistor; resistances in ohms inside the logarithms.
  • No unique fit exists when R₁R₂R₃ = 1 Ω³ (ln R₁ + ln R₂ + ln R₃ = 0); the page then asks for other points. Real thermistor points in the kΩ range are far from this.

References

  • J.S. Steinhart and S.R. Hart
  • Deep-Sea Research 15 (1968) 497

Questions and answers

Why three points?

The equation has three unknowns, A, B and C.

How accurate is it?

Typically within a few hundredths of a kelvin over 100 K.

Is the default a real thermistor?

Points typical of a 10 k NTC; use your own calibration data.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.