FireCADCalc

Probe in Hot Gas: Radiation Error of a Thermocouple or Lance

Temperature a bare thermocouple, probe or soot-blower lance reaches in hot gas with cooler walls around it, and its radiation error.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: Ganapathy Q8.09b: 2000 °F gas, 400 °F walls, h 15 (book 1250 °F)Low load h 5 (book 970 °F)Bare thermocouple in 600 °C duct, walls 450 °C

Results

Effective emissivity taken as ε_p·ε_w, as in Ganapathy's example; conduction along the probe is neglected. A suction (aspirated) pyrometer raises h and cuts the error.

Probe temperature678.70°C
Radiation error (gas minus probe)414.63K
Heat flux through the probe surface35.314kW/m²

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Ganapathy Q8.09b: 2000 °F gas, 400 °F walls, h 15 (book 1250 °F). The inputs, in the units selected above:

InputValue
Gas temperature1,093.3 °C
Surrounding wall temperature204.44 °C
Gas-to-probe convective coefficient85.174 W/(m²·K)
Probe emissivity90.000 %
Wall emissivity90.000 %

Applying the formula below gives:

ResultValue
Probe temperature678.71 °C
Radiation error (gas minus probe)414.62 K
Heat flux through the probe surface35.315 kW/m²

Open this example in the calculator and change any input.

Formula

\(h_c(T_g - T_p) = \sigma\varepsilon_p\varepsilon_w\left(T_p^4 - T_w^4\right)\)

Variables

Symbol Meaning SI unit
\(T_g\) Gas temperature K
\(T_w\) Surrounding wall temperature K
\(h_c\) Gas-to-probe convective coefficient W/(m²·K)
\(\varepsilon_p\) Probe emissivity -
\(\varepsilon_w\) Wall emissivity -
\(T_p\) Probe temperature K
\(T_g - T_p\) Radiation error (gas minus probe) K
\(q\) Heat flux through the probe surface W/m²

Method and standards

Convection–radiation balance.

Where it is used

  • Furnace gas temperature measurement.
  • Soot blower and probe material selection.

Common mistakes

  • Taking the reading as the gas temperature.
  • Ignoring low gas velocity at part load.

Assumptions and limits

  • Steady state; no conduction along the probe.
  • Effective emissivity ε_p ε_w as in Ganapathy. For a small probe in a large enclosure the classical exchange uses ε_p alone, which gives a larger radiation error than shown here.

References

  • Ganapathy
  • Industrial Boilers and Heat Recovery Steam Generators (Marcel Dekker, 2003)
  • Q8.09b (soot blower lance temperature: convection–radiation balance)

Questions and answers

Why does a thermocouple read low in a furnace?

It loses heat by radiation to cooler walls; it settles where convection from the gas equals that loss, below the gas temperature.

What does Ganapathy's example give?

Gas at 2,000 °F, walls at 400 °F, h 15 Btu/(ft²·h·°F): the lance reaches about 1,250 °F; at h 5 only about 970 °F.

How can the error be reduced?

Raise h (suction pyrometer), shield the probe, or use a lower-emissivity sheath.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.