FireCADCalc

Wet-Bulb Temperature from Dry Bulb and Relative Humidity

Thermodynamic wet-bulb temperature, dew point, humidity ratio and enthalpy of moist air from dry-bulb temperature, relative humidity and pressure.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textileIAPWS-IF97 (water and steam)

Inputs

Examples: 35 °C, 40 %28 °C, 80 % at 1,000 m

Results

Thermodynamic (adiabatic saturation) wet bulb by ASHRAE eq. (33); a well-ventilated psychrometer reads close to it. Saturation pressure from IAPWS-IF97.

Wet-bulb temperature25.120°C
Wet-bulb depression2.8803K
Dew point24.225°C
Humidity ratio21.671g/kg
Enthalpy (per kg dry air)83.497kJ/kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 35 °C, 40 %. The inputs, in the units selected above:

InputValue
Dry-bulb temperature35.000 °C
Relative humidity40.000 %
Barometric pressure101.33 kPa

Applying the formula below gives:

ResultValue
Wet-bulb temperature23.934 °C
Wet-bulb depression11.066 K
Dew point19.384 °C
Humidity ratio14.133 g/kg
Enthalpy (per kg dry air)71.478 kJ/kg

Open this example in the calculator and change any input.

Formula

\(W = \frac{(2501 - 2.326t_{wb})W_s^* - 1.006(t - t_{wb})}{2501 + 1.86t - 4.186t_{wb}}, \quad W = 0.622\frac{\varphi p_s}{p - \varphi p_s}\)

Variables

Symbol Meaning SI unit
\(t\) Dry-bulb temperature K
\(\varphi\) Relative humidity -
\(p\) Barometric pressure Pa
\(t_{wb}\) Wet-bulb temperature K
\(t - t_{wb}\) Wet-bulb depression K
\(t_{dp}\) Dew point K
\(W\) Humidity ratio kg/kg
\(h\) Enthalpy (per kg dry air) J/kg

Method and standards

ASHRAE eq. (33), solved for t_wb.

Where it is used

  • Cooling tower and evaporative cooler design.
  • Heat stress and comfort checks.

Common mistakes

  • Confusing wet bulb with dew point.
  • Ignoring altitude (barometric pressure).

Assumptions and limits

  • 0–100 °C; wet bulb above 0 °C.

References

  • ASHRAE Handbook—Fundamentals (2017)
  • ch. 1
  • eq. (33) for the thermodynamic wet bulb; IAPWS-IF97 saturation pressure

Questions and answers

Why does wet bulb matter?

It limits evaporative cooling: cooling towers and evaporative coolers cannot cool water or air below it.

Is wet bulb the same as dew point?

No: dew point is lower (unless the air is saturated); wet bulb lies between dew point and dry bulb.

What do the defaults represent?

Hot, moderately dry summer air at sea-level pressure.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.