FireCADCalc

Equilibrium Constant and Conversion from the Gibbs Energy

Equilibrium constant from the standard Gibbs energy of reaction, and the equilibrium conversion for A ⇌ B or a gas-phase A ⇌ 2B at a pressure.

Distillery and ethanolRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: A ⇌ B, ΔG° +5 kJ/mol, 600 KA ⇌ 2B at 10 bar, ΔG° −10 kJ/mol, 800 K, 2 mol inert

Results

Ideal gas with standard state 1 bar for A ⇌ 2B; ideal solution for A ⇌ B. Raising pressure lowers the conversion of mole-increasing reactions; inerts raise it.

Equilibrium constant4.4970
Equilibrium conversion of A45.876%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: A ⇌ B, ΔG° +5 kJ/mol, 600 K. The inputs, in the units selected above:

InputValue
Standard Gibbs energy of reaction at T5.0000 kJ/mol
Temperature326.85 °C
ReactionA ⇌ B (no mole change)
Pressure (for A ⇌ 2B)1.0132 bar
Inert moles per mole of A fed0 -

Applying the formula below gives:

ResultValue
Equilibrium constant0.36705
Equilibrium conversion of A26.850 %

Open this example in the calculator and change any input.

Formula

\(K = \exp\left(-\frac{\Delta G^\circ}{RT}\right), \quad X_e = \frac{K}{1 + K}\ (A\rightleftharpoons B), \quad K = \frac{(2X/n_T)^2}{(1 - X)/n_T}\frac{p}{p^\circ}\ (A\rightleftharpoons2B)\)

Variables

Symbol Meaning SI unit
\(\Delta G^\circ\) Standard Gibbs energy of reaction at T J/mol
\(T\) Temperature K
\(\text{type}\) Reaction -
\(p\) Pressure (for A ⇌ 2B) Pa
\(n_I\) Inert moles per mole of A fed -
\(K\) Equilibrium constant -
\(X_e\) Equilibrium conversion of A -

Method and standards

Chemical equilibrium.

Where it is used

  • Feasibility screening of reactions.
  • Choosing temperature and pressure.

Common mistakes

  • Using ΔG° at 298 K for a hot reactor.
  • Forgetting the standard-state pressure.

Assumptions and limits

  • Ideal gas or ideal solution.
  • Only two stoichiometries are covered, A ⇌ B and A ⇌ 2B; ΔG° must be the value at the reaction temperature T (use the van 't Hoff calculator to move it from 298 K). R from CODATA.

References

  • K = exp(−ΔG°/RT) (Smith, Van Ness and Abbott, Introduction to Chemical Engineering Thermodynamics, ch. 13)

Questions and answers

Why does ΔG° = 0 give 50 % for A ⇌ B?

K = 1, so at equilibrium A and B are equal.

Why does pressure matter for A ⇌ 2B?

The reaction makes more moles; higher pressure pushes it back (Le Chatelier). Inerts lower the partial pressures and help.

What do the defaults represent?

A reaction with ΔG° = +5 kJ/mol at 600 K: K about 0.37.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.