Worked example
Example: Toluene vapour 500 K (Perry's example: 25.2 mW/(m K)). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Temperature | 226.85 °C |
| Critical temperature | 318.60 °C |
| Acentric factor | 0.26400 - |
| Molar mass | 92.138 kg/kmol |
| Gas viscosity at T | 0.011408 cP |
| Ideal-gas heat capacity at T (J/(mol·K)) | 170.78 - |
| Molecule shape (Stiel–Thodos) | Nonlinear |
Applying the formula below gives:
| Result | Value |
|---|---|
| Heat capacity at constant volume (J/(mol·K)) | 162.47 |
| Thermal conductivity, Stiel–Thodos | 0.025226 W/(m·K) |
| Chung Ψ | 7.2931 |
| Thermal conductivity, Chung | 0.028155 W/(m·K) |
Open this example in the calculator and change any input.
Formula
\(\frac{kM}{\eta C_v} = 1.15 + 2.033\frac{R}{C_v}\ \text{(nonlinear)}, \quad 1.30 + 1.7614\frac{R}{C_v} - \frac{0.3523}{T_r}\ \text{(linear)}, \quad 2.5\ \text{(monatomic)}\)
\(\frac{kM}{\eta C_v} = \frac{3.75\Psi}{C_v/R}, \quad \Psi = 1 + \alpha\frac{0.215 + 0.28288\alpha - 1.061\beta + 0.26665Z}{0.6366 + \beta Z + 1.061\alpha\beta}\)
\(\alpha = \frac{C_v}{R} - 1.5, \quad \beta = 0.7862 - 0.7109\omega + 1.3168\omega^2, \quad Z = 2.0 + 10.5T_r^2\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(T\) | Temperature | K |
| \(T_c\) | Critical temperature | K |
| \(\omega\) | Acentric factor | - |
| \(M\) | Molar mass | kg/kmol |
| \(\eta\) | Gas viscosity at T | Pa·s |
| \(C_p^\circ\) | Ideal-gas heat capacity at T (J/(mol·K)) | - |
| \(\text{shape}\) | Molecule shape (Stiel–Thodos) | - |
| \(C_v\) | Heat capacity at constant volume (J/(mol·K)) | - |
| \(k_{ST}\) | Thermal conductivity, Stiel–Thodos | W/(m·K) |
| \(\Psi\) | Chung Ψ | - |
| \(k_{Chung}\) | Thermal conductivity, Chung | W/(m·K) |
Method and standards
Stiel–Thodos and Chung–Lee–Starling.
Where it is used
- Heat transfer to organic vapours.
- Gas-side coefficients.
Common mistakes
- Using at high pressure.
- Entering C_p in J/(kg·K) instead of per mole.
Assumptions and limits
- Low pressure; C_v = C_p° − R.
- C_p° is per mole, in J/(mol·K), and at least 2.5R; a per-kg value must be multiplied by the molar mass first.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 2
- Eqs. (2-103) to (2-108) (Stiel–Thodos; Chung, Lee and Starling) with the toluene example
Questions and answers
What does Perry's example give?
Toluene vapour at 500 K: 25.2 mW/(m·K) by Stiel–Thodos, 18 % below DIPPR's 30.76.
Why is viscosity an input?
Both methods are Eucken-type: they scale the viscosity by the heat capacity, because the same molecular collisions carry momentum and energy.
Which result should I use?
Chung's, for polar gases; the difference between the two is a fair guide to the uncertainty.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.