Worked example
Example: Oxygen-like, 25 to 500 °C. The inputs, in the units selected above:
| Input | Value |
|---|---|
| a (J/(mol·K)) | 28.110 - |
| b (J/(mol·K²)) | -3.6800e-06 - |
| c (J/(mol·K³)) | 1.7460e-05 - |
| d (J/(mol·K⁴)) | -1.0650e-08 - |
| Temperature 1 | 25.000 °C |
| Temperature 2 | 500.00 °C |
| Molar mass | 32.000 kg/kmol |
Applying the formula below gives:
| Result | Value |
|---|---|
| c_p at T₁ (J/(mol·K)) | 29.379 |
| c_p at T₂ (J/(mol·K)) | 33.622 |
| Mean c_p between T₁ and T₂ | 0.98398 kJ/(kg·K) |
| Enthalpy change | 467.39 kJ/kg |
| Entropy change at constant pressure | 0.92748 kJ/(kg·K) |
Open this example in the calculator and change any input.
Formula
\(c_p = a + bT + cT^2 + dT^3, \quad \Delta h = \int c_p\,dT, \quad \Delta s = \int\frac{c_p}{T}dT\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(a\) | a (J/(mol·K)) | - |
| \(b\) | b (J/(mol·K²)) | - |
| \(c\) | c (J/(mol·K³)) | - |
| \(d\) | d (J/(mol·K⁴)) | - |
| \(T_1\) | Temperature 1 | K |
| \(T_2\) | Temperature 2 | K |
| \(M\) | Molar mass | kg/kmol |
| \(c_p(T_1)\) | c_p at T₁ | - |
| \(c_p(T_2)\) | c_p at T₂ (J/(mol·K)) | - |
| \(\bar c_p\) | Mean c_p between T₁ and T₂ | J/(kg·K) |
| \(\Delta h\) | Enthalpy change | J/kg |
| \(\Delta s\) | Entropy change at constant pressure | J/(kg·K) |
Method and standards
Polynomial integration (per mole, then per kg).
Where it is used
- Gas heating duties.
- Combustion and reactor balances.
Common mistakes
- Using coefficients outside their range.
- Mixing molar and mass bases.
Assumptions and limits
- Ideal gas.
- Coefficients must give c_p in J/(mol·K) with T in kelvin (kJ/(kmol·K) has the same numbers). Sets in calories or with T in °C must be converted first. c_p at T₁ and T₂ is shown per mole; the mean c_p, Δh and Δs are per kg.
- The coefficients' fitted temperature range is not checked: keep T₁ and T₂ inside it.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 2 (ideal-gas heat capacity correlations)
- Integration of c_p(T) (definitions)
Questions and answers
Why a mean c_p?
Δh = c̄_p ΔT exactly when c̄_p is the integral average between the two temperatures.
Where do coefficients come from?
Property databases and textbooks; check the temperature range they were fitted for.
What do the defaults represent?
Illustrative coefficients similar to oxygen's, between 25 and 500 °C; they are not taken from a particular table, so enter your own.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.