FireCADCalc

Pulveriser Mill Outlet Temperature and Air to Coal Ratio

Mill outlet temperature of a coal pulveriser from the primary air flow and temperature, coal feed and moisture, by a heat balance, with the air to coal ratio.

Thermal power plantProcess steam and utilitiesChemical and fertiliserPulp and paperASME PTC 4 (fired steam generators)IAPWS-IF97 (water and steam)BoilerBurner and furnace

Inputs

Examples: Bituminous 30 t/h, 15 % moisture, 60 t/h air at 280 °CIndian coal 40 t/h, 12 %, 72 t/h air at 260 °CLignite 25 t/h, 35 %, 75 t/h air at 320 °C

From the coal analysis or the mill maker.
About 0.01 for temperate air, up to 0.02 to 0.03 for humid tropical air; from the psychrometric chart at the air intake.

Results

The mill outlet temperature limit depends on the coal's volatile matter (fire and explosion risk); check the mill maker's limit.

Mill outlet temperature79.652°C
Primary air (dry) to coal ratio3.0000kg/kg
Water evaporated in the mill6.9444t/h
Heat taken by drying and heating the coal5,263.3kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Bituminous 30 t/h, 15 % moisture, 60 t/h air at 280 °C. The inputs, in the units selected above:

InputValue
Raw coal feed to the mill30.000 t/h
Total moisture of the raw coal15.000 %
Moisture left in the pulverised coal2.0000 %
Raw coal temperature30.000 °C
Specific heat of the dry coal1.2500 kJ/(kg·K)
Primary air flow, dry60.000 t/h
Primary air temperature at the mill inlet280.00 °C
Primary air humidity, kg water per kg dry air0.013000 kg/kg
Mill grinding power (enters as heat)150.00 kW
Heat lost from the mill casing and ducts50.000 kW

Applying the formula below gives:

ResultValue
Mill outlet temperature91.381 °C
Primary air (dry) to coal ratio2.0000 kg/kg
Water evaporated in the mill3.9796 t/h
Heat taken by drying and heating the coal3,394.7 kW

Open this example in the calculator and change any input.

Formula

\(w = \frac{M_{in} - M_{out}}{1 - M_{out}}, \quad \dot m_w = \dot m_c w\)

\(Q_c = \dot m_w [h_v(T_o) - h_f(T_c)] + \dot m_c (1 - M_{in}) c_c (T_o - T_c) + \dot m_c (M_{in} - w) [h_f(T_o) - h_f(T_c)]\)

\(h_a(T) = h_{da}(T) + x_a h_{v,ig}(T), \quad \dot m_a [h_a(T_{in}) - h_a(T_o)] + P_m - Q_l = Q_c\)

Variables

Symbol Meaning SI unit
\(\dot m_c\) raw coal feed kg/s
\(M_{in}\) total moisture of the raw coal -
\(M_{out}\) moisture left in the pulverised coal -
\(T_c\) raw coal temperature K
\(c_c\) specific heat of the dry coal J/(kg·K)
\(P_m\) mill grinding power, entering as heat W
\(Q_l\) mill casing and duct heat loss W
\(\dot m_w\) water evaporated kg/s
\(Q_c\) heat taken by the coal side W
\(\dot m_a\) primary air flow, dry air kg/s
\(T_{in}\) primary air temperature at the mill inlet K
\(T_o\) mill outlet temperature K
\(r\) primary air (dry) to coal ratio kg/kg
\(h_v\) water vapour enthalpy at T_o and 1 psia J/kg
\(h_f\) liquid water enthalpy J/kg
\(h_a\) humid air enthalpy per kg dry air: dry air plus x_a kg of ideal-gas water vapour J/kg
\(x_a\) primary air humidity, kg water vapour per kg dry air kg/kg
\(h_{da}\) dry air enthalpy J/kg
\(h_{v,ig}\) ideal-gas water vapour enthalpy J/kg
\(w\) water evaporated per kg raw coal kg/kg

Method and standards

A heat balance on the mill: the hot primary air gives up heat between the mill inlet and outlet temperatures; with the grinding power (which ends as heat) it evaporates the surface moisture and warms the coal and the water left in it. The evaporated water leaves as vapour (IAPWS-IF97 at 1 psia, as ASME PTC 4 treats flue gas moisture); the primary air is humid: per kg of dry air it carries x_a kg of water vapour, and its enthalpy is dry air plus that vapour as an ideal gas from NIST Shomate data, the basis ASME PTC 4 uses for moisture in air. The outlet temperature is found by solving the balance.

Where it is used

  • Predicting mill outlet temperature after a change in coal moisture.
  • Checking the air heater outlet needed for a target outlet temperature.
  • Commissioning and tuning primary air control.

Common mistakes

  • Using wet-basis and dry-basis moisture interchangeably.
  • Forgetting the grinding heat.
  • Treating the air to coal ratio as fixed across the load range.

Assumptions and limits

  • Steady state; the primary air flow is dry air, and the humidity entered is carried as vapour.
  • If the heat supplied exceeds the coal's need even at the inlet air temperature, the outlet is shown at that temperature with a note.
  • Surface moisture removed is total moisture less the moisture left in the pulverised coal.
  • No allowance for seal air or leakage.

References

  • Mill heat balance
  • IAPWS-IF97
  • ASME PTC 4 (vapour at 1 psia)

Questions and answers

What outlet temperature will a mill reach?

In the example, 30 t/h of 15 % moisture coal with 60 t/h of air at 280 °C reaches about 91 °C at the outlet (primary air humidity 0.013 kg/kg).

What air to coal ratio do mills run at?

Roughly 1.5 to 2.5 kg air per kg coal for vertical spindle mills; the mill maker sets the curve against load.

Why limit the outlet temperature?

Hot, high-volatile coal dust can ignite in the mill and pipes; the limit falls as volatile matter rises.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.