FireCADCalc

Bulk Sugar Store Capacity

Sugar a prismatic bulk store holds from its width, length, side-wall height and the sugar's angle of repose, with Hugot's bulk densities (ch. 36–37).

Sugar mill and cogeneration

Inputs

Examples: 40 x 100 m, 3 m walls, 34°Narrow store 36°

Hugot: unbuttressed walls rarely above 3 m.
Hugot: 33–36° dry; up to 50–53° wet.
Hugot: 800–900 kg/m³; 1 000 at 6 m depth.

Results

The prism ignores the sloping ends; a store fed from a ridge belt loses a little at each end. Keep belts to the store below about 20° slope.

The store is short for its width: the sloping ends cut the volume by roughly 7 %, more than the prism shows.

Check that the roof clears the ridge: the pile rises 11.6 m above the floor.

Height of the pile at the ridge11.582m
Cross-section of sugar176.02m²
Volume14,082m³
Sugar held11,970t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 40 x 100 m, 3 m walls, 34°. The inputs, in the units selected above:

InputValue
Store width40.000 m
Store length100.00 m
Side-wall height3.0000 m
Angle of repose of the sugar34.000 °
Bulk density in the pile880.00 kg/m³

Applying the formula below gives:

ResultValue
Height of the pile at the ridge16.490 m
Cross-section of sugar389.80 m²
Volume38,980 m³
Sugar held34,303 t

Open this example in the calculator and change any input.

Formula

\(h_r = h_w + \frac{W}{2}\tan\alpha, \quad A = W h_w + \frac{W^2}{4}\tan\alpha, \quad V = A\ell, \quad M = \rho V\)

Variables

Symbol Meaning SI unit
\(W\) Store width m
\(\ell\) Store length m
\(h_w\) Side-wall height m
\(\alpha\) Angle of repose of the sugar rad
\(\rho\) Bulk density in the pile kg/m³
\(h_r\) Height of the pile at the ridge m
\(A\) Cross-section of sugar m²
\(V\) Volume m³
\(M\) Sugar held kg

Method and standards

Geometry of a prismatic pile.

Where it is used

  • Sizing bulk stores.
  • Season storage planning.

Common mistakes

  • Using bag-store density for bulk.
  • Ignoring the end slopes on short stores.

Assumptions and limits

  • Prismatic pile filled to the angle of repose; the ridge height is not checked against the roof (a note gives it).
  • The sloping ends are ignored. With the pile sloping at the angle of repose at both ends too, the ends hold about W³ tan α/12 less than the prism; a note gives the share when it exceeds 5 % (short stores).

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 36
  • bulk storage (Fig. 36.1)
  • pp. 819–820; ch. 37
  • densities
  • p. 832

Questions and answers

Why does bulk sugar keep better than bagged?

The pile's surface forms a crust that keeps moisture out; dry sugar keeps for years.

Which density?

Hugot: 800–900 kg/m³, rising with depth as the pile compacts.

Why low side walls?

Sugar presses hard on walls; economic stores keep them near 3 m and let the pile rise to the roof.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.