FireCADCalc

Cane Feeding Table Area and Motor (Hugot)

Lateral feeding table area for a crushing rate, its length for a width, the table motor, and the auxiliary carrier motor, by Hugot eqns 1.7, 1.9 and 1.10.

Sugar mill and cogenerationElectric motor

Inputs

Examples: 250 TCH, two tables60 TCH, one table

Hugot recommends two tables above about 70 t cane/h.

Results

Table speed is usually 3–6 m/min; the auxiliary carrier runs at about half the main carrier speed.

Total table area40.000m²
Area of each table40.000m²
Length of each table6.6667m
Motor of each table7.3550kW
Auxiliary carrier motor0kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 250 TCH, two tables. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Number of feeding tables2.0000 -
Width of each table (along the carrier)8.0000 m
Loaded area of the auxiliary (cross) carrier20.000 m²

Applying the formula below gives:

ResultValue
Total table area166.67 m²
Area of each table83.333 m²
Length of each table10.417 m
Motor of each table15.323 kW
Auxiliary carrier motor6.8000 kW

Open this example in the calculator and change any input.

Formula

\(S = \tfrac{2}{3}A \;[\mathrm{m^2},\ A\ \mathrm{in\ t/h}], \quad T = 0.25\,S_i \;[\mathrm{metric\ hp}], \quad T_x = 0.34\,S_x \;[\mathrm{kW}], \quad S_i = \frac{S}{n_t}, \quad \ell = \frac{S_i}{W}\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(n_t\) Number of feeding tables -
\(W\) Width of each table (along the carrier) m
\(S_x\) Loaded area of the auxiliary (cross) carrier m²
\(S\) Total table area m²
\(S_i\) Area of each table m²
\(\ell\) Length of each table m
\(T\) Motor of each table W
\(T_x\) Auxiliary carrier motor W

Method and standards

Hugot's empirical rules from installed tables (metric horsepower, 75 kgf·m/s).

Where it is used

  • Sizing feeding tables for a new or expanded mill.
  • Checking table motors.

Common mistakes

  • Using the area of one table for the total.
  • Mixing metric and British horsepower.

Assumptions and limits

  • Hugot's rules for chain tables feeding a cane carrier; whole numbers of tables. A note appears with one table above about 70 t cane/h.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 1
  • eqns 1.7 (S = 2A/3 m²)
  • 1.9 (T = 0.25 S metric hp) and 1.10 (T = 0.34 S kW)

Questions and answers

Where does S = 2A/3 come from?

Hugot's rule from installed tables: about two-thirds of a square metre of table per tonne of cane crushed per hour.

One table or two?

Above about 70 t cane/h Hugot prefers two tables sharing the area, so one can feed while the other is loaded.

Why is the motor so small?

The table moves slowly (3–6 m/min) and the cane rests on chains running on rollers.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.