Worked example
Example: 250 TCH carrier. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Crushing rate | 250.00 t/h |
| Carrier speed | 8.0000 m/min |
| Loaded length of the carrier | 40.000 m |
| Total length of apron (both runs) | 90.000 m |
| Height the cane is lifted | 7.0000 m |
| Chain mass per metre, each of the two chains | 25.000 kg/m |
| Slat mass per metre of carrier length | 75.000 kg/m |
| Friction coefficient, loaded run | 0.30000 - |
| Friction coefficient, return run | 0.15000 - |
| Gearing and drive factor | 1.4500 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Cane on the loaded length | 20.833 t |
| Weight of chains and slats on one run | 5.6250 t |
| Friction power | 16.649 kW |
| Lifting power | 6.9123 kW |
| Carrier power | 23.561 kW |
| Rough estimate (3Z_t + A)/20 hp | 19.123 kW |
| Installed power, Hugot rule (3Z_t + A)/10 hp | 38.246 kW |
Open this example in the calculator and change any input.
Formula
\(Q = \frac{A\,Z_c}{u}, \quad K = \frac{Z_t}{2}(2p + p')\)
\(P_f = [(Q + K)f + K f']\,g\,u\,\lambda, \quad P_e = A\,g\,H\,\lambda, \quad P = P_f + P_e\)
\(P_r = \frac{3Z_t + A}{20}, \quad P_i = \frac{3Z_t + A}{10} \;[\mathrm{metric\ hp}]\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(A\) | Crushing rate | kg/s |
| \(u\) | Carrier speed | m/s |
| \(Z_c\) | Loaded length of the carrier | m |
| \(Z_t\) | Total length of apron (both runs) | m |
| \(H\) | Height the cane is lifted | m |
| \(p\) | Chain mass per metre, each of the two chains | kg/m |
| \(p'\) | Slat mass per metre of carrier length | kg/m |
| \(f\) | Friction coefficient, loaded run | - |
| \(f'\) | Friction coefficient, return run | - |
| \(\lambda\) | Gearing and drive factor | - |
| \(Q\) | Cane on the loaded length | kg |
| \(K\) | Weight of chains and slats on one run | kg |
| \(P_f\) | Friction power | W |
| \(P_e\) | Lifting power | W |
| \(P\) | Carrier power | W |
| \(P_r\) | Rough estimate (3Z_t + A)/20 hp | W |
| \(P_i\) | Installed power, Hugot rule (3Z_t + A)/10 hp | W |
Method and standards
Hugot's force balance on the loaded and return runs plus the work of lifting the cane, multiplied by a drive factor.
Where it is used
- Motor sizing for main and feeder cane carriers.
- Checking an existing carrier after a crush increase.
Common mistakes
- Using the chain mass for both chains as p.
- Taking the speed in m/min in the SI form.
Assumptions and limits
- Steady load evenly spread on the loaded length.
- The slat mass is per metre of carrier length for the whole width (Hugot's figure per metre of width times the width). The return-run friction default is a FireCAD starting value.
References
- Hugot
- Handbook of Cane Sugar Engineering
- 3rd ed. (Elsevier, 1986)
- ch. 2
- eqns 2.9–2.15
- pp. 27–29
Questions and answers
Why the factor λ?
It covers gearing losses and the extra effort of starting and of uneven loading; Hugot uses 1.4–1.5.
Which friction for the loaded run?
0.30 when the slats run on rollers, 0.60 when they slide on rails.
What is Z_t?
The total apron length, both runs; each run carries half the chain and slat weight.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.