Worked example
Example: 30 MPa inside, 100 x 160 mm bore and outside. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Internal pressure (gauge) | 30.000 MPa |
| External pressure (gauge) | 0 MPa |
| Inside radius | 50.000 mm |
| Outside radius | 80.000 mm |
Applying the formula below gives:
| Result | Value |
|---|---|
| Hoop stress at the bore | 68.462 MPa |
| Hoop stress at the outside | 38.462 MPa |
| Radial stress at the bore | -30.000 MPa |
| Radial stress at the outside | 0 MPa |
| Longitudinal stress (closed ends) | 19.231 MPa |
| Stress intensity at the bore (Tresca) | 98.462 MPa |
Open this example in the calculator and change any input.
Formula
\(A = \frac{p_i r_i^2 - p_o r_o^2}{r_o^2 - r_i^2}, \quad B = \frac{(p_i - p_o) r_i^2 r_o^2}{r_o^2 - r_i^2}\)
\(\sigma_\theta = A + \frac{B}{r^2}, \quad \sigma_r = A - \frac{B}{r^2}, \quad \sigma_l = A\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(p_i\) | Internal pressure (gauge) | Pa |
| \(p_o\) | External pressure (gauge) | Pa |
| \(r_i\) | Inside radius | m |
| \(r_o\) | Outside radius | m |
| \(\sigma_{\theta,i}\) | Hoop stress at the bore | Pa |
| \(\sigma_{\theta,o}\) | Hoop stress at the outside | Pa |
| \(\sigma_{r,i}\) | Radial stress at the bore | Pa |
| \(\sigma_{r,o}\) | Radial stress at the outside | Pa |
| \(\sigma_l\) | Longitudinal stress (closed ends) | Pa |
| \(\sigma_{\theta,i} - \sigma_{r,i}\) | Stress intensity at the bore (Tresca) | Pa |
| \(A, B\) | Lamé constants | Pa, N |
Method and standards
Lamé's elastic solution for a long cylinder under internal and external pressure; the longitudinal stress is for closed ends.
Where it is used
- Hydraulic cylinders, high-pressure tubing and accumulators.
- Shrink fits and press fits (with the interface pressure).
- Checking thin-wall estimates.
Common mistakes
- Using diameters where radii are wanted.
- Treating the result as a code thickness.
- Forgetting stress concentration at ports.
Assumptions and limits
The longitudinal stress A is for closed ends carrying the end thrust; with open ends (a tube whose thrust is taken elsewhere, a press-fitted sleeve) it is zero. Hoop and radial stresses are the same either way.
No yield check: compare the stress intensity at the bore (Tresca) with the allowable stress of the code or the material's yield strength.
Elastic, homogeneous, far from ends.
Tensile positive.
References
- G. Lamé (1852); Timoshenko
- Strength of Materials Part II
Questions and answers
What is the bore stress of a 100 mm bore, 160 mm outside cylinder at 30 MPa?
Hoop 68.5 MPa at the bore and 38.5 MPa outside; radial −30 MPa at the bore. The thin-wall formula would give 50 MPa.
Where is the stress highest?
At the bore, where hoop and radial stresses differ most; the Tresca stress intensity there is 98.5 MPa.
When is a cylinder thick?
When the wall is more than about a tenth of the radius; then thin-wall formulas under-estimate the bore stress.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.