FireCADCalc

Two Pumps in Parallel or Series (Operating Point)

Operating flow and head of one pump and of two identical pumps in parallel or in series on a system curve with static head, and the flow gained.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserHydraulic Institute (pumps)Pump

Inputs

Examples: Two pumps in parallel, static 20 mTwo pumps in parallel, friction systemTwo pumps in series, static 40 m

One pump's curve

System curve

Results

Flow with two pumps106.90m³/h
Head with two pumps57.143m
Flow through each pump53.452m³/h
Flow gained over one pump6.9045%
Flow with one pump100.00m³/h
Head with one pump50.000m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Two pumps in parallel, static 20 m. The inputs, in the units selected above:

InputValue
Two pumpsIn parallel
Pump shut-off head (zero flow)60.000 m
Rated flow100.00 m³/h
Head at rated flow50.000 m
Static head of the system20.000 m
A known flow of the system100.00 m³/h
Head the system needs at that flow50.000 m

Applying the formula below gives:

ResultValue
Flow with two pumps110.94 m³/h
Head with two pumps56.923 m
Flow through each pump55.470 m³/h
Flow gained over one pump10.940 %
Flow with one pump100.00 m³/h
Head with one pump50.000 m

Open this example in the calculator and change any input.

Formula

Pump curve through the shut-off head and the rated point, system curve through the static head and a known point:

\(H_{pump} = H_0 - a\,Q^2,\ \ a = \frac{H_0 - H_r}{Q_r^2} \qquad H_{sys} = H_s + k\,Q^2,\ \ k = \frac{H_d - H_s}{Q_d^2}\)

\(Q_1 = \sqrt{\frac{H_0 - H_s}{a + k}} \qquad \text{parallel: } Q_2 = \sqrt{\frac{H_0 - H_s}{a/4 + k}} \qquad \text{series: } Q_2 = \sqrt{\frac{2H_0 - H_s}{2a + k}}\)

\(H_1 = H_s + k\,Q_1^2 \qquad H_2 = H_s + k\,Q_2^2 \qquad \Delta Q = \frac{Q_2}{Q_1} - 1\)

Variables

Symbol Meaning SI unit
\(\text{mode}\) two pumps in parallel or in series –
\(H_0\) shut-off head of one pump m
\(Q_r\) rated flow of one pump m³/s
\(H_r\) head at rated flow m
\(H_s\) static head of the system m
\(Q_d\) a known flow of the system m³/s
\(H_d\) head the system needs at that flow m
\(Q_2\) flow with two pumps m³/s
\(H_2\) head with two pumps m
\(Q_{each}\) flow through each pump m³/s
\(\Delta Q\) flow gained over one pump –
\(Q_1\) flow with one pump m³/s
\(H_1\) head with one pump m

Method and standards

Intersection of the combined pump curve with the system curve, the method of Karassik's Pump Handbook: in parallel the flows add at equal head, in series the heads add at equal flow. Both curves are represented by parabolas through the points you enter.

Where it is used

  • Combining pumps for flow or head.
  • Standby and duty pump arrangements.
  • Checking operating points with a system curve.

Common mistakes

  • Assuming two parallel pumps give twice the flow on a steep system curve.
  • Running mismatched pumps in parallel.
  • Ignoring the second pump's NPSH in series.

Assumptions and limits

  • Identical pumps; the parabola through shut-off and the rated point approximates the real curve near the rated point.
  • System curve with constant static head and losses proportional to Q².
  • Check that each pump in parallel stays above its minimum flow and each pump alone stays inside its curve.

References

  • Karassik et al.
  • Pump Handbook (parallel and series operation); ANSI/HI 1.3

Questions and answers

Do two pumps in parallel double the flow?

No. The system needs more head at more flow, so the second pump adds much less. With a pump of 60 m shut-off and 50 m at 100 m³/h on a system with 20 m static head, one pump gives 100 m³/h and two give 111 m³/h.

When does parallel operation pay?

When most of the system head is static. On a system that is all friction the gain is even smaller (7 % in the example).

When are pumps put in series?

When the system needs more head than one pump gives. Two in series on a 40 m static system deliver 163 m³/h against 100 m³/h for one pump.

Method and article reviewed by FireCAD engineering on 10 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.