FireCADCalc

Multistage Compressor Interstage Pressure and Intercooler Duty

Equal-ratio interstage pressures of a multistage compressor, stage discharge temperatures, shaft power and intercooler duty for an ideal gas.

Thermal power plantRefinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: Air 1 to 30 bar(a), 3 stagesTwo stages to 8 bar(a)

Results

Equal ratios minimise power when every stage starts at the same temperature; the first intercooler cools stage-1 gas, the others later-stage gas. No aftercooler included. Pressure drop through intercoolers is neglected.

Pressure ratio per stage3.0936
Discharge pressure of stage 13.1346bar
Discharge temperature of stage 1174.30°C
Discharge temperature of later stages189.06°C
Total shaft power444.58kW
Duty of each intercooler134.96kW
Total intercooler duty284.74kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Air 1 to 30 bar(a), 3 stages. The inputs, in the units selected above:

InputValue
Suction pressure (absolute)1.0132 bar
Final discharge pressure (absolute)30.000 bar
Number of stages3.0000 -
First-stage suction temperature30.000 °C
Gas temperature after each intercooler40.000 °C
Isentropic efficiency per stage80.000 %
Ratio of specific heats1.4000 -
Molar mass28.960 kg/kmol
Mass flow3,600.0 kg/h

Applying the formula below gives:

ResultValue
Pressure ratio per stage3.0936
Discharge pressure of stage 13.1346 bar
Discharge temperature of stage 1174.30 °C
Discharge temperature of later stages189.06 °C
Total shaft power444.58 kW
Duty of each intercooler134.96 kW
Total intercooler duty284.74 kW

Open this example in the calculator and change any input.

Formula

\(r = \left(\frac{p_2}{p_1}\right)^{1/N}, \quad T_d = T_s + \frac{T_s\left(r^{(\gamma - 1)/\gamma} - 1\right)}{\eta_s}, \quad P = \dot mc_p\sum(T_d - T_s), \quad Q_{ic} = \dot mc_p(T_d - T_{ic})\)

Variables

Symbol Meaning SI unit
\(p_1\) Suction pressure (absolute) Pa
\(p_2\) Final discharge pressure (absolute) Pa
\(N\) Number of stages -
\(T_1\) First-stage suction temperature K
\(T_{ic}\) Gas temperature after each intercooler K
\(\eta_s\) Isentropic efficiency per stage -
\(\gamma\) Ratio of specific heats -
\(M\) Molar mass kg/kmol
\(\dot m\) Mass flow kg/s
\(r\) Pressure ratio per stage -
\(p_{i,1}\) Discharge pressure of stage 1 Pa
\(T_{d,1}\) Discharge temperature of stage 1 K
\(T_{d,n}\) Discharge temperature of later stages K
\(P\) Total shaft power W
\(Q_{ic}\) Duty of each intercooler W
\(Q_{ic,total}\) Total intercooler duty W

Method and standards

Ideal-gas staged compression.

Where it is used

  • Air and process gas compressor checks.
  • Intercooler and cooling-water sizing.

Common mistakes

  • Gauge pressures.
  • Forgetting interstage pressure drop.

Assumptions and limits

  • Ideal gas; constant c_p; equal ratios.

References

  • Ideal-gas staged compression with equal pressure ratios (definitions; Perry's Chemical Engineers' Handbook, 9th ed. (McGraw-Hill, 2019), sec. 10, compressors)

Questions and answers

Why equal pressure ratios?

With full intercooling back to the same temperature, equal ratios give the least total work.

Where does the intercooler heat go?

To cooling water; it is about the same as the stage work, a good source of low-grade heat.

What do the defaults give?

Air 1 to 30 bar(a) in three stages: ratio 3.1 per stage and about 174 °C stage-1 discharge at 80 % efficiency.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.