FireCADCalc

Carbon Equivalent (CE IIW) and Pcm for Welding

Carbon equivalent of a steel by the IIW formula and the Ito–Bessyo Pcm from its chemical analysis, used to judge weldability and preheat.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserBoiler

Inputs

Examples: Structural plate C 0.18 Mn 1.2 Si 0.3SA-516 Gr 70: C 0.22 Mn 1.1 Si 0.251¼Cr–½Mo: C 0.12 Mn 0.45 Si 0.6 Cr 1.25 Mo 0.55

Results

Use the ladle or certificate analysis. Preheat comes from your welding code (for example EN 1011-2 or AWS D1.1) using CE or Pcm with thickness, hydrogen level and heat input.

Carbon equivalent (IIW)0.43067%
Cracking parameter (Ito–Bessyo)0.26950%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Structural plate C 0.18 Mn 1.2 Si 0.3. The inputs, in the units selected above:

InputValue
Carbon0.18000 %
Manganese1.2000 %
Silicon0.30000 %
Chromium0.10000 %
Molybdenum0.050000 %
Vanadium0.020000 %
Nickel0.10000 %
Copper0.15000 %
Boron0 %

Applying the formula below gives:

ResultValue
Carbon equivalent (IIW)0.43067 %
Cracking parameter (Ito–Bessyo)0.26950 %

Open this example in the calculator and change any input.

Formula

\(CE_{IIW} = C + \frac{Mn}{6} + \frac{Cr + Mo + V}{5} + \frac{Ni + Cu}{15}\)

\(P_{cm} = C + \frac{Si}{30} + \frac{Mn + Cu + Cr}{20} + \frac{Ni}{60} + \frac{Mo}{15} + \frac{V}{10} + 5B\)

Variables

Symbol Meaning SI unit
\(C\) carbon mass %
\(Mn\) manganese mass %
\(Si\) silicon mass %
\(Cr\) chromium mass %
\(Mo\) molybdenum mass %
\(V\) vanadium mass %
\(Ni\) nickel mass %
\(Cu\) copper mass %
\(B\) boron mass %
\(CE_{IIW}\) carbon equivalent mass %
\(P_{cm}\) cracking parameter mass %

Method and standards

IIW carbon equivalent and the Ito–Bessyo cracking parameter, both as given in EN 1011-2 Annex C.

Where it is used

  • Welding procedure qualification.
  • Repair welding of old steels.
  • Material substitution checks.

Common mistakes

  • Using specification maxima instead of actual analysis.
  • Using CE(IIW) on low-carbon micro-alloyed steels.
  • Forgetting boron in Pcm.

Assumptions and limits

  • Steel analysis in mass %; formulas apply to carbon and low-alloy steels.
  • CE and Pcm come out in mass % (shown as, for example, 0.43 %); codes quote the same number without the % sign (CE = 0.43).

References

  • IIW carbon equivalent; Ito–Bessyo Pcm; EN 1011-2 Annex C

Questions and answers

What is CE for C 0.18, Mn 1.2, Si 0.3, Cr 0.1, Mo 0.05, V 0.02, Ni 0.1, Cu 0.15?

CE(IIW) 0.43 and Pcm 0.27.

Which one should I use?

CE(IIW) for most carbon–manganese steels; Pcm for low-carbon (under about 0.12 % C) high-strength steels.

Does CE give the preheat?

Not alone: the welding code combines it with thickness, hydrogen level and heat input.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.