FireCADCalc

Two-Way Slab Load Shared to Supporting Beams

Load each beam takes from a two-way slab by the 45° tributary method (triangles and trapezoids), with equivalent uniform loads for bending and shear.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 4 × 6 m panel at 10 kN/m²Square 5 × 5 m at 8 kN/m²

Results

45° lines from each corner split the panel into two triangles (to the short-span beams) and two trapezoids (to the long-span beams). Equivalent UDLs give the same mid-span moment or end shear in a simply supported beam.

Total load on each short-span beam50.000kN
Total load on each long-span beam50.000kN
Equivalent UDL for moment, short beam13.333kN/m
Equivalent UDL for moment, long beam13.333kN/m
Equivalent UDL for shear, short beam10.000kN/m
Equivalent UDL for shear, long beam10.000kN/m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 4 × 6 m panel at 10 kN/m². The inputs, in the units selected above:

InputValue
Slab load (dead + imposed)10.000 kPa
Short span4.0000 m
Long span6.0000 m

Applying the formula below gives:

ResultValue
Total load on each short-span beam40.000 kN
Total load on each long-span beam80.000 kN
Equivalent UDL for moment, short beam13.333 kN/m
Equivalent UDL for moment, long beam17.037 kN/m
Equivalent UDL for shear, short beam10.000 kN/m
Equivalent UDL for shear, long beam13.333 kN/m

Open this example in the calculator and change any input.

Formula

\(W_s = \frac{w l_x^2}{4}, \quad W_l = \frac{w l_x (2l_y - l_x)}{4}\)

\(w_{e,s} = \frac{wl_x}{3}, \quad w_{e,l} = \frac{wl_x}{6}\left[3 - \left(\frac{l_x}{l_y}\right)^2\right] \quad \text{(moment)}\)

\(w_{v,s} = \frac{wl_x}{4}, \quad w_{v,l} = \frac{wl_x}{4}\left(2 - \frac{l_x}{l_y}\right) \quad \text{(shear)}\)

Variables

Symbol Meaning SI unit
\(w\) Slab load (dead + imposed) Pa
\(l_x\) Short span m
\(l_y\) Long span m
\(W_s\) Total load on each short-span beam N
\(W_l\) Total load on each long-span beam N
\(w_{e,s}\) Equivalent UDL for moment, short beam N/m
\(w_{e,l}\) Equivalent UDL for moment, long beam N/m
\(w_{v,s}\) Equivalent UDL for shear, short beam N/m
\(w_{v,l}\) Equivalent UDL for shear, long beam N/m

Method and standards

Tributary areas.

Where it is used

  • Beam design in framed buildings.
  • Platform and floor checks.

Common mistakes

  • Using the moment equivalent for shear.
  • Adding beam self weight twice.

Assumptions and limits

  • Uniform load; 45° division of a two-way panel.
  • For l_y > 2 l_x the slab is one-way: the page warns, and the 45° split then overstates the short-span beam load.

References

  • Yield-line (45°) tributary division and equivalent uniform loads (Punmia, Reinforced Concrete Structures)

Questions and answers

Why do the short beams get triangles?

Load flows to the nearest support; the 45° lines from the corners meet sooner along the short side.

When is a slab one-way?

When the long span exceeds about twice the short span; then nearly all load goes to the long beams.

What do the defaults represent?

A 4 × 6 m panel carrying 10 kN/m².

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.