FireCADCalc

Liquid Heat Capacity by Lee–Kesler Corresponding States

Liquid heat capacity from the ideal-gas heat capacity, critical temperature and acentric factor by Lee–Kesler corresponding states (Perry's Eq. 2-55).

Refinery and petrochemicalChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 1,4-Dioxane 320 K (Perry's example: Cp/R 18.58)Toluene 300 K

Results

Perry's: about 4 % for organics other than strongly polar or associating ones. Estimate for design; use measured data where they exist.

Liquid heat capacity (J/(mol·K))154.49
Liquid specific heat1.7534kJ/(kg·K)
Residual heat capacity (J/(mol·K))55.211

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1,4-Dioxane 320 K (Perry's example: Cp/R 18.58). The inputs, in the units selected above:

InputValue
Temperature46.850 °C
Critical temperature323.85 °C
Acentric factor0.27930 -
Ideal-gas heat capacity at T (J/(mol·K))99.275 -
Molar mass88.106 kg/kmol

Applying the formula below gives:

ResultValue
Liquid heat capacity (J/(mol·K))154.49
Liquid specific heat1.7534 kJ/(kg·K)
Residual heat capacity (J/(mol·K))55.211

Open this example in the calculator and change any input.

Formula

\(\frac{C_p - C_p^\circ}{R} = 1.586 + \frac{0.49}{1 - T_r} + \omega\left[4.2775 + \frac{6.3(1 - T_r)^{1/3}}{T_r} + \frac{0.4355}{1 - T_r}\right]\)

Variables

Symbol Meaning SI unit
\(T\) Temperature K
\(T_c\) Critical temperature K
\(\omega\) Acentric factor -
\(C_p^\circ\) Ideal-gas heat capacity at T (J/(mol·K)) -
\(M\) Molar mass kg/kmol
\(C_p\) Liquid heat capacity (J/(mol·K)) -
\(c_p\) Liquid specific heat J/(kg·K)
\(C_p - C_p^\circ\) Residual heat capacity (J/(mol·K)) -

Method and standards

Lee–Kesler corresponding states.

Where it is used

  • Liquid heating duties for solvents.
  • Heat balances for organic streams.

Common mistakes

  • Entering C_p° at another temperature.
  • Using for water or alcohols.

Assumptions and limits

  • Nonpolar or slightly polar organic liquids.
  • The liquid state is not checked: make sure T lies between the melting and boiling points. At low reduced temperatures (below about 0.4) a note appears, because the (1 − T_r)^⅓/T_r term then grows large.

References

  • Perry's Chemical Engineers' Handbook
  • 9th ed. (McGraw-Hill, 2019)
  • sec. 2
  • Eq. (2-55) (Lee–Kesler) with the 1
  • 4-dioxane example

Questions and answers

What does Perry's example give?

1,4-dioxane at 320 K: C_p/R = 18.58, C_p = 154.5 J/(mol·K), 4.6 % below DIPPR.

Where do I get C_p°?

From ideal-gas heat-capacity polynomials or group contributions at the same temperature.

Why does it fail near T_c?

Liquid C_p really does rise steeply there; the equation's 1/(1 − T_r) terms follow it but lose accuracy.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.