Worked example
Example: Bagasse, coal, husk. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Steam pressure (absolute) | 11.000 bar |
| Steam condition | Superheated at the temperature below |
| Steam temperature (superheated only) | 185.00 °C |
| Feedwater temperature | 80.000 °C |
| Fuel 1 price per tonne | 1,800.0 - |
| Fuel 1 GCV | 9,600.0 kJ/kg |
| Efficiency on fuel 1 | 70.000 % |
| Fuel 2 price per tonne | 9,000.0 - |
| Fuel 2 GCV | 23,000 kJ/kg |
| Efficiency on fuel 2 | 82.000 % |
| Fuel 3 price per tonne | 4,500.0 - |
| Fuel 3 GCV | 13,500 kJ/kg |
| Efficiency on fuel 3 | 75.000 % |
Applying the formula below gives:
| Result | Value |
|---|---|
| Heat per kg of steam | 2,447.4 kJ/kg |
| Fuel cost per tonne of steam, fuel 1 | 655.57 |
| Fuel cost per tonne of steam, fuel 2 | 1,167.9 |
| Fuel cost per tonne of steam, fuel 3 | 1,087.8 |
Open this example in the calculator and change any input.
Formula
\(C_i = \frac{h_s - h_{fw}}{GCV_i \eta_i} c_i\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(p\) | Steam pressure (absolute) | Pa |
| \(T\) | Steam temperature (superheated only) | K |
| \(\text{state}\) | Steam condition: dry saturated or superheated | - |
| \(T_{fw}\) | Feedwater temperature | K |
| \(c_1\) | Fuel 1 price per tonne | - |
| \(GCV_1\) | Fuel 1 GCV | J/kg |
| \(\eta_1\) | Efficiency on fuel 1 | - |
| \(c_2\) | Fuel 2 price per tonne | - |
| \(GCV_2\) | Fuel 2 GCV | J/kg |
| \(\eta_2\) | Efficiency on fuel 2 | - |
| \(c_3\) | Fuel 3 price per tonne | - |
| \(GCV_3\) | Fuel 3 GCV | J/kg |
| \(\eta_3\) | Efficiency on fuel 3 | - |
| \(\Delta h\) | Heat per kg of steam | J/kg |
| \(C_1\) | Fuel cost per tonne of steam, fuel 1 | - |
| \(C_2\) | Fuel cost per tonne of steam, fuel 2 | - |
| \(C_3\) | Fuel cost per tonne of steam, fuel 3 | - |
Method and standards
Energy balance: fuel per tonne of steam is the heat added from feedwater to steam (IAPWS-IF97) over each fuel's GCV and efficiency, times its price.
Where it is used
- Fuel purchase decisions.
- Off-season fuel planning.
Common mistakes
- Mixing gross and net bases.
Assumptions and limits
- Fuel cost only.
- Steam dry saturated or superheated as chosen.
- Feedwater must be liquid at the steam pressure.
References
- Fuel per tonne of steam = Δh/(GCV η); Δh from IAPWS-IF97
Questions and answers
Why include efficiency for each fuel?
Wet biomass burns at lower efficiency, which raises its cost per tonne of steam.
Delivered price?
Use the price at the boiler, including transport and handling.
Currency?
Any, consistently.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.