FireCADCalc

Bagasse Drying and Pelletising: Fuel and Steam Gain

Pellets made by drying bagasse to a lower moisture, the energy to pelletise and the steam gained per kg of original bagasse, after Hugot's preface.

Sugar mill and cogenerationBoiler

Inputs

Examples: Hugot figures: 48 -> 8 % moisturePellets at 15 %

Results

Hugot: about 560 g of pellets per kg of bagasse, 80 kWh per tonne of pellets, and 4.8 kg of steam per kg of pellets against 2.2 per kg of bagasse: about 22 % more steam.

Pellets11.765t/h
Pellets per kg bagasse0.58824
Water removed8.2353t/h
Pelletising power1,058.8kW
Gross steam gain over burning the bagasse (drying heat and pelletising power not deducted)23.249%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Hugot figures: 48 -> 8 % moisture. The inputs, in the units selected above:

InputValue
Bagasse30.000 t/h
Bagasse moisture48.000 %
Pellet moisture8.0000 %
Pelletising energy per tonne of pellets80.000 kWh/t
Steam per kg of pellets4.8000 -
Steam per kg of bagasse2.2000 -

Applying the formula below gives:

ResultValue
Pellets16.957 t/h
Pellets per kg bagasse0.56522
Water removed13.043 t/h
Pelletising power1,356.5 kW
Gross steam gain over burning the bagasse (drying heat and pelletising power not deducted)23.320 %

Open this example in the calculator and change any input.

Formula

\(y = \frac{1 - w_0}{1 - w_1}, \quad \dot m_p = yB, \quad P = e\,\dot m_p, \quad \text{gain} = \frac{y\,r_p}{r_b} - 1\)

Variables

Symbol Meaning SI unit
\(B\) Bagasse kg/s
\(w_0\) Bagasse moisture -
\(w_1\) Pellet moisture -
\(e\) Pelletising energy per tonne of pellets J/kg
\(r_p\) Steam per kg of pellets -
\(r_b\) Steam per kg of bagasse -
\(\dot m_p\) Pellets kg/s
\(y\) Pellets per kg bagasse -
\(\dot m_w\) Water removed kg/s
\(P\) Pelletising power W
\(y\,r_p/r_b - 1\) Gross steam gain over burning the bagasse (drying heat and pelletising power not deducted) -

Method and standards

Dry-solids balance with Hugot's figures.

Where it is used

  • Surplus bagasse studies.
  • Off-season fuel planning.

Common mistakes

  • Ignoring drying energy.
  • Comparing steam at different conditions.

Assumptions and limits

  • Same boiler conditions for both fuels.
  • The steam gain is gross: the heat to dry the bagasse (about 0.4 kg of water per kg of bagasse at the defaults) and the pelletising power are not deducted. It is a real gain only if the drying heat would otherwise be wasted (flue gas).
  • Steam per kg of pellets and of bagasse are your inputs; the pellet figure is not tied to the pellet moisture.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • preface to the third edition (bagasse pelletisation)
  • Dry-solids balance

Questions and answers

Why pelletise?

Dry pellets store well and burn with far more steam per kg; surplus bagasse becomes a saleable fuel.

Where does the drying heat come from?

Usually flue gas from the boilers; the steam gain counts only if the drying heat is otherwise wasted.

How dense are pellets?

Bulk about 720–880 kg/m³, against 120–200 for bagasse.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.