FireCADCalc

Donnelly Chute Feed Pressure and Thickness (Hugot)

Pressure of the bagasse column at the foot of a Donnelly chute, Hugot eqn 8.9, and the chute thickness he recommends from the delivery opening.

Sugar mill and cogeneration

Inputs

Examples: First mill chuteFinal mill with feed roller

Hugot: about 400 kg/m³ for the first mill (300–600).
Hugot: 0.25–0.30.
Hugot: first and second mills 16 without a feed roller, 14 with one; final mill 12 and 10.

Results

E/D is 0.13, outside the 0.40–0.75 of the roller diameter that Hugot finds in practice (thicker at lower mill speeds): check the ratio m and the opening.

Feed pressure at the chute foot8.7111kPa
Recommended chute thickness at the bottom120.00mm
Thickness / roller diameter0.13129

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: First mill chute. The inputs, in the units selected above:

InputValue
Height of bagasse in the chute2.5000 m
Bulk density of the bagasse in the chute400.00 kg/m³
Chute angle to the horizontal80.000 °
Friction coefficient of bagasse on the plates0.27000 -
Delivery work opening of the mill20.000 mm
Chute thickness / delivery opening16.000 -
Roller diameter1.0000 m

Applying the formula below gives:

ResultValue
Feed pressure at the chute foot9.1979 kPa
Recommended chute thickness at the bottom320.00 mm
Thickness / roller diameter0.32000

Open this example in the calculator and change any input.

Formula

\(F = Z\,d\,g\,(\sin\beta - \varphi\cos\beta), \quad E = m\,e_A, \quad \frac{E}{D}\)

Variables

Symbol Meaning SI unit
\(Z\) Height of bagasse in the chute m
\(d\) Bulk density of the bagasse in the chute kg/m³
\(\beta\) Chute angle to the horizontal rad
\(\varphi\) Friction coefficient of bagasse on the plates -
\(e_A\) Delivery work opening of the mill m
\(m\) Chute thickness / delivery opening -
\(D\) Roller diameter m
\(F\) Feed pressure at the chute foot Pa
\(E\) Recommended chute thickness at the bottom m
\(E/D\) Thickness / roller diameter -

Method and standards

Hugot's static balance of the bagasse column on an inclined plate.

Where it is used

  • Designing and checking Donnelly chutes.
  • Diagnosing poor mill feeding.

Common mistakes

  • Using whole-cane density for prepared bagasse.
  • Taking the chute angle from the vertical.

Assumptions and limits

  • Static column; no pressure feeder.
  • A note flags E/D outside Hugot's practical 0.40–0.75.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 8
  • eqns 8.6–8.9 and recommended thicknesses
  • pp. 84–88

Questions and answers

What drives the feed?

The weight of the bagasse column, less the friction on the chute plates, pushes the blanket into the feed nip.

Why relate the thickness to the delivery opening?

The chute must pass the same fibre as the mill; Hugot gives the thickness as a multiple of the delivery opening.

Best chute angle?

Close to vertical; Hugot finds about 80° best, with the front plate a degree flatter.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.