FireCADCalc

Total Cane Preparation Power

Installed and absorbed power for knives and shredder together from a total kW per tonne fibre per hour and the knife share, after Hugot ch. 6.

Sugar mill and cogenerationElectric motor

Inputs

Examples: Average 40 kW/tfhHeavy preparation

Hugot: 24–60, about 40 kW/(t fibre/h) on average; heavy-duty shredders much more.
Hugot: 46 % knives, 54 % shredder on average.
Hugot: 50–60 %.

Results

Installed preparation power1,450.0kW
Installed in the knives667.00kW
Installed in the shredder783.00kW
Mean absorbed power797.50kW
Absorbed energy per tonne of cane3.1900kWh/t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Average 40 kW/tfh. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Fibre % cane14.500 %
Total installed preparation power per tonne fibre per hour40.000 kWh/t
Share of the installed power in the knives46.000 %
Absorbed / installed55.000 %

Applying the formula below gives:

ResultValue
Installed preparation power1,450.0 kW
Installed in the knives667.00 kW
Installed in the shredder783.00 kW
Mean absorbed power797.50 kW
Absorbed energy per tonne of cane3.1900 kWh/t

Open this example in the calculator and change any input.

Formula

\(P_i = e\,A f, \quad P_k = s_k P_i, \quad P_s = (1 - s_k)P_i, \quad P_a = \varphi P_i, \quad E_c = \frac{P_a}{A}\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(f\) Fibre % cane -
\(e\) Total installed preparation power per tonne fibre per hour J/kg
\(s_k\) Share of the installed power in the knives -
\(\varphi\) Absorbed / installed -
\(P_i\) Installed preparation power W
\(P_k\) Installed in the knives W
\(P_s\) Installed in the shredder W
\(P_a\) Mean absorbed power W
\(E_c\) Absorbed energy per tonne of cane J/kg

Method and standards

Specific power on the fibre rate.

Where it is used

  • Budgeting power for preparation.
  • Comparing preparation intensity between mills.

Common mistakes

  • Using power per tonne cane with fibre rate.
  • Forgetting the knives when quoting shredder power.

Assumptions and limits

  • Averages from practice. The specific power is per tonne of fibre per hour (shown in kWh/t = kW per t/h), not per tonne of cane; E_c is the absorbed energy per tonne of cane.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 6
  • total power for cane preparation
  • p. 70

Questions and answers

What is typical?

Hugot reports 24–60 kW installed per tonne fibre per hour, about 40 on average, slightly more in the shredder than the knives.

Why more power for better preparation?

Finer preparation opens more cells and raises extraction; heavy shredders use 40–50 kW/(t fibre/h) on their own.

Absorbed or installed?

Plants absorb about half to 60 % of the installed figure on average.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.