FireCADCalc

Cane Knife Set: Knives, Cut and Tip Speed (Hugot)

Cane layer on the carrier, number of knives for a pitch, share of cane cut for a knife clearance, and tip speed of a cane knife set, by Hugot eqns 3.1–3.4.

Sugar mill and cogeneration

Inputs

Examples: First set, 50 mm pitchSecond set, 22 mm pitch

Hugot: 150 tangled whole cane, 175 parallel, about 300 for cane already cut by a first set.
First set about 50 mm; second and third 20–22 mm.

Results

Knives run at 400–720 rpm; Hugot recommends about 500 rpm for the first set and 600 for the second.

Height of the cane layer1,736.1mm
Number of knives (even)38.000
Share of the layer passing uncut17.280%
Share of the layer cut82.720%
Knife tip speed50.265m/s

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: First set, 50 mm pitch. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Carrier speed8.0000 m/min
Carrier width2.0000 m
Bulk density of the cane reaching the knives150.00 kg/m³
Knife pitch (spacing along the shaft)50.000 mm
Clearance between knife tips and carrier300.00 mm
Knife tip circle diameter1.6000 m
Knife shaft speed600.00 rpm

Applying the formula below gives:

ResultValue
Height of the cane layer1,736.1 mm
Number of knives (even)38.000
Share of the layer passing uncut17.280 %
Share of the layer cut82.720 %
Knife tip speed50.265 m/s

Open this example in the calculator and change any input.

Formula

\(h = \frac{A}{u\,L\,d}, \quad N = \left\lfloor \frac{L}{p} - 1 \right\rfloor\ \text{rounded down to even}, \quad i = \min\left(1, \frac{r}{h}\right), \quad K = 1 - i, \quad v_t = \pi D_k n\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(u\) Carrier speed m/s
\(L\) Carrier width m
\(d\) Bulk density of the cane reaching the knives kg/m³
\(p\) Knife pitch (spacing along the shaft) m
\(r\) Clearance between knife tips and carrier m
\(D_k\) Knife tip circle diameter m
\(n\) Knife shaft speed 1/s
\(h\) Height of the cane layer m
\(N\) Number of knives (even) -
\(i\) Share of the layer passing uncut -
\(K\) Share of the layer cut -
\(v_t\) Knife tip speed m/s

Method and standards

Hugot's continuity of the cane layer on the carrier and the geometry of the knife clearance.

Where it is used

  • Specifying knife sets and their settings.
  • Checking the cut achieved after a crush increase.

Common mistakes

  • Taking the layer height after levelling as the height of tangled cane.
  • Using the shaft speed in rpm in the SI form.

Assumptions and limits

  • Even layer across the carrier width. With a clearance of at least the layer height nothing is cut (a note says so). A note appears outside 400–720 rpm.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 3
  • eqns 3.1–3.4
  • pp. 37–41

Questions and answers

Why an even number of knives?

Knives are mounted in opposed pairs to balance the rotor; Hugot rounds an odd count down to the next even number.

How close should the first set run?

Hugot puts the first-set clearance near a quarter of the layer height; closer settings cut more cane but need more power.

Which bulk density?

Whole tangled cane on the carrier is about 150 kg/m³; after a first set it packs to about 300 kg/m³.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.