FireCADCalc

Cane Knife Set Power per Tonne Fibre

Installed and absorbed power of a cane knife set from the fibre rate and an installed kW per tonne fibre per hour (Hugot ch. 3), with the turbine-drive allowance.

Sugar mill and cogenerationSteam turbineElectric motor

Inputs

Examples: Knives as shredder, motorLevellers, turbine

Hugot (South African practice): levellers 7, levellers running in reverse 10, knives working as a shredder 20 (first and second sets), third set 12 kW/(t fibre/h).

Results

Hugot (after Farrell) rates a turbine drive about one-third above the motor, because a turbine cannot take the motor's short overloads.

Fibre rate24.000t/h
Installed power (electric motor rating)168.00kW
Mean absorbed power100.80kW
Drive rating (motor: P_i; turbine: 1.33 P_i)223.44kW
Installed power per tonne cane per hour1.1200kWh/t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Knives as shredder, motor. The inputs, in the units selected above:

InputValue
Crushing rate250.00 t/h
Fibre % cane14.500 %
Installed power per tonne of fibre per hour (kW/(t fibre/h), not per t cane)20.000 kWh/t
Mean absorbed power / installed power60.000 %
DriveElectric motor

Applying the formula below gives:

ResultValue
Fibre rate36.250 t/h
Installed power (electric motor rating)725.00 kW
Mean absorbed power435.00 kW
Drive rating (motor: P_i; turbine: 1.33 P_i)725.00 kW
Installed power per tonne cane per hour2.9000 kWh/t

Open this example in the calculator and change any input.

Formula

\(P_i = e\,A f, \quad P_a = \varphi P_i, \quad P_d = P_i\ \text{(motor)},\ 1.33\,P_i\ \text{(turbine)}, \quad \frac{P_i}{A}\)

Variables

Symbol Meaning SI unit
\(A\) Crushing rate kg/s
\(f\) Fibre % cane -
\(e\) Installed power per tonne of fibre per hour (kW/(t fibre/h), not per t cane) J/kg
\(\varphi\) Mean absorbed power / installed power -
\(\text{drive}\) Drive -
\(A f\) Fibre rate kg/s
\(P_i\) Installed power (electric motor rating) W
\(P_a\) Mean absorbed power W
\(P_d\) Drive rating (motor: P_i; turbine: 1.33 P_i) W
\(P_i/A\) Installed power per tonne cane per hour J/kg

Method and standards

Specific power on the fibre rate, as tabulated by Hugot.

Where it is used

  • Sizing knife drives.
  • Comparing preparation power between mills.

Common mistakes

  • Using power per tonne cane with a fibre rate.
  • Sizing on the mean instead of the installed figure.

Assumptions and limits

  • Specific power from practice; adjust for cane variety and harvesting. It is per tonne of fibre per hour, shown in kWh/t (= kW per t/h); a figure per tonne of cane is about 7 times smaller.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 3
  • Tables 3.1–3.2 and pp. 43–45

Questions and answers

Why per tonne of fibre?

The work of cutting depends on the fibre passing, not on the juice; fibre rate compares mills fairly.

How much of the installed power is used?

On average about 60 %; the rest covers peaks when thick layers or tangled cane arrive.

Why more for a turbine?

A motor can take short overloads; a turbine slows down, so its rating is about a third higher.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.