FireCADCalc

Restriction Orifice Sizing: Liquid or Gas

Bore of a restriction orifice for a liquid at a set pressure drop or for a gas, choked or subcritical, with the cavitation index for liquid service.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: Liquid: 2 kg/s water, 10 bar dropGas: 0.1 kg/s air choked from 20 bar(a)Gas: 0.1 kg/s air, 20 to 15 bar(a), not choked

Gas only. Above the critical pressure p* the flow is subcritical and the bore is sized by the subcritical equation.

Results

Downstream pressure not entered: choked flow is assumed. If the downstream pressure is above p*, enter it; the choked bore would then be too small.

Thin plate, single hole; velocity of approach neglected (small bore relative to pipe). Use several plates in series for large liquid drops.

Orifice bore6.6881mm
Orifice area35.132mm²
Cavitation index (p₁ − p_v)/Δp (liquid)0
Critical downstream pressure (gas)10.566bar

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Liquid: 2 kg/s water, 10 bar drop. The inputs, in the units selected above:

InputValue
ServiceLiquid
Mass flow7,200.0 kg/h
Upstream pressure (absolute)20.000 bar
Pressure drop (liquid)10.000 bar
Liquid density (liquid)998.00 kg/m³
Vapour pressure (liquid)3.1700 kPa
Gas temperature (gas)26.850 °C
Gas molar mass28.960 kg/kmol
Ratio of specific heats1.4000 -
Downstream pressure, absolute (gas; 0 = assume choked)0 bar
Discharge coefficient0.61000 -

Applying the formula below gives:

ResultValue
Orifice bore9.6664 mm
Orifice area73.387 mm²
Cavitation index (p₁ − p_v)/Δp (liquid)1.9968
Critical downstream pressure (gas)0 bar

Open this example in the calculator and change any input.

Formula

\(A = \frac{\dot m}{C_d\sqrt{2\rho\Delta p}}\ \text{(liquid)}, \quad A = \frac{\dot m}{C_dp_1\sqrt{\frac{\gamma}{RT_1}\left(\frac{2}{\gamma + 1}\right)^{\frac{\gamma + 1}{\gamma - 1}}}}\ \text{(choked gas)}\)

\(A = \frac{\dot m}{C_d p_1\sqrt{\frac{2\gamma}{(\gamma - 1)RT_1}\left[\left(\frac{p_2}{p_1}\right)^{2/\gamma} - \left(\frac{p_2}{p_1}\right)^{(\gamma + 1)/\gamma}\right]}}\ \text{(gas, } p_2 > p^*\text{)}, \quad p^* = p_1\left(\frac{2}{\gamma + 1}\right)^{\frac{\gamma}{\gamma - 1}}, \quad R = \frac{R_u}{M}\)

Variables

Symbol Meaning SI unit
\(\text{service}\) Service -
\(\dot m\) Mass flow kg/s
\(p_1\) Upstream pressure (absolute) Pa
\(\Delta p\) Pressure drop (liquid) Pa
\(\rho\) Liquid density (liquid) kg/m³
\(p_v\) Vapour pressure (liquid) Pa
\(T_1\) Gas temperature (gas) K
\(M\) Gas molar mass kg/kmol
\(\gamma\) Ratio of specific heats -
\(p_2\) Downstream pressure, absolute (gas; 0 = assume choked) Pa
\(C_d\) Discharge coefficient -
\(R\) Specific gas constant J/(kg·K)
\(R_u\) Universal gas constant, 8 314.462 618 J/(kmol·K)
\(d\) Orifice bore m
\(A\) Orifice area m²
\(\sigma\) Cavitation index (p₁ − p_v)/Δp (liquid) -
\(p^*\) Critical downstream pressure (gas) Pa

Method and standards

Orifice equation for liquids; isentropic flow of an ideal gas through the orifice for gases, choked when p₂ ≤ p* and subcritical above it.

Where it is used

  • Pump recirculation lines.
  • Purge and vent flow limiting.

Common mistakes

  • Using a metering-orifice C for a restriction plate.
  • Single plate for a flashing drop.

Assumptions and limits

  • Sharp-edged; small β.
  • Gas: if the downstream pressure is left at 0, choked flow is assumed and the page says so; enter p₂ to have subcritical flow sized correctly.
  • The cavitation index of 2 used for the warning is a common screening level, not a limit from a standard; use the plate maker's data for the design.

References

  • Orifice equation (liquid) and critical flow through an orifice (gas) (definitions; Lipták, Instrument Engineers' Handbook, 4th ed. (CRC Press))

Questions and answers

Where are restriction orifices used?

Pump minimum-flow lines, purge and bleed lines, vent limits and fixed pressure letdowns.

Why multi-stage for big drops?

One plate taking a large liquid drop flashes and cavitates; several plates share the drop.

What do the defaults represent?

2 kg/s of water dropping 10 bar from 20 bar(a).

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.