FireCADCalc

Insulation Thickness to Prevent Condensation on a Cold Pipe

Least insulation thickness that keeps a cold pipe's outer surface above the ambient dew point (plus a margin), by the ISO 12241 heat transfer method.

Refinery and petrochemicalChemical and fertiliserFood, dairy and textileISO 12241 (thermal insulation)

Inputs

Examples: DN100 at 5 °C in 32 °C, 80 %Bright cladding, 90 % humidityMild case: bare pipe stays dry

Low for bright metal cladding, which needs more thickness.

Results

Round up to the next thickness made. ISO 12241 still air; draughts help, bright cladding and high humidity need more.

Ambient dew point28.177°C
Insulation thickness needed117.44mm
Surface temperature at that thickness28.677°C
Heat gain per metre at that thickness3.0014W/m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: DN100 at 5 °C in 32 °C, 80 %. The inputs, in the units selected above:

InputValue
Pipe outer diameter114.30 mm
Insulation conductivity0.035000 W/(m·K)
Pipe (fluid) temperature5.0000 °C
Ambient air temperature32.000 °C
Ambient relative humidity80.000 %
Surface emissivity90.000 %
Safety margin above the dew point0.50000 K

Applying the formula below gives:

ResultValue
Ambient dew point28.111 °C
Insulation thickness needed24.498 mm
Surface temperature at that thickness28.611 °C
Heat gain per metre at that thickness14.555 W/m

Open this example in the calculator and change any input.

Formula

\(\text{find } s: \ T_s(s) = T_{dp} + \Delta T_m\)

Variables

Symbol Meaning SI unit
\(D_o\) Pipe outer diameter m
\(\lambda\) Insulation conductivity W/(m·K)
\(T_w\) Pipe (fluid) temperature K
\(T_a\) Ambient air temperature K
\(\varphi\) Ambient relative humidity -
\(\varepsilon\) Surface emissivity -
\(\Delta T_m\) Safety margin above the dew point K
\(T_{dp}\) Ambient dew point K
\(s\) Insulation thickness needed m
\(T_s\) Surface temperature at that thickness K
\(q'\) Heat gain per metre at that thickness W/m

Method and standards

Bisection on the ISO 12241 surface temperature.

Where it is used

  • Chilled water, brine and refrigerant lines.
  • Cold process pipes.

Common mistakes

  • Average instead of design humidity.
  • Ignoring cladding emissivity.

Assumptions and limits

  • Still air, steady state.

References

  • ISO 12241 insulated pipe method (engine InsulatedPipe)
  • thickness by bisection on the surface temperature; dew point from IAPWS

Questions and answers

DN100 at 5 °C in 32 °C, 80 % air?

About 25 mm with ε 0.9 and λ 0.035; bright cladding needs much more.

Why does humidity matter so much?

Near saturation the dew point approaches the air temperature, and the needed thickness climbs steeply.

Which conditions to design for?

The worst humid ambient the pipe will see, not the average.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.