FireCADCalc

Chilled Water Pipe Heat Gain and Surface Condensation

Heat gain of an insulated chilled water pipe by the ISO 12241 method, the outer surface temperature against the dew point, and the water temperature rise.

Refinery and petrochemicalChemical and fertiliserFood, dairy and textileISO 12241 (thermal insulation)

Inputs

Examples: DN150 at 7 °C, 40 mm, 35 °C 70 %Bare DN50 at 6 °C sweatingBrine at −10 °C, 75 mm, aluminium cladding

4186 J/(kg·K) for water; about 3 600 for 30 % glycol and lower for strong brines: from the maker's data.

Results

The surface is below the dew point: it will sweat. Thicken the insulation (see the condensation thickness calculator).

Heat gain per metre48.329W/m
Total heat gain2.4164kW
Outer surface temperature6.0000°C
Ambient dew point21.388°C
Margin (negative: condensation)-15.388K
Water temperature rise0.28863K

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: DN150 at 7 °C, 40 mm, 35 °C 70 %. The inputs, in the units selected above:

InputValue
Pipe outer diameter168.30 mm
Insulation thickness40.000 mm
Insulation conductivity0.035000 W/(m·K)
Chilled water or brine temperature7.0000 °C
Ambient air temperature35.000 °C
Ambient relative humidity70.000 %
Surface emissivity90.000 %
Pipe length200.00 m
Water flow72,000 kg/h
Specific heat of the water or brine4.1860 kJ/(kg·K)

Applying the formula below gives:

ResultValue
Heat gain per metre14.531 W/m
Total heat gain2.9062 kW
Outer surface temperature32.697 °C
Ambient dew point28.701 °C
Margin (negative: condensation)3.9961 K
Water temperature rise0.034714 K

Open this example in the calculator and change any input.

Formula

\(q' = \frac{T_a - T_w}{\frac{\ln(D/D_o)}{2\pi\lambda} + \frac{1}{h_{se}\pi D}}, \quad \Delta T_w = \frac{q' L}{\dot m c_p}\)

Variables

Symbol Meaning SI unit
\(D_o\) Pipe outer diameter m
\(s\) Insulation thickness m
\(\lambda\) Insulation conductivity W/(m·K)
\(T_w\) Chilled water or brine temperature K
\(T_a\) Ambient air temperature K
\(\varphi\) Ambient relative humidity -
\(\varepsilon\) Surface emissivity -
\(L\) Pipe length m
\(\dot m\) Water flow kg/s
\(c_p\) Specific heat of the water or brine J/(kg·K)
\(q'\) Heat gain per metre W/m
\(\dot Q\) Total heat gain W
\(T_s\) Outer surface temperature K
\(T_{dp}\) Ambient dew point K
\(T_s - T_{dp}\) Margin (negative: condensation) K
\(\Delta T_w\) Water temperature rise K

Method and standards

ISO 12241 conduction and surface coefficient.

Where it is used

  • Chilled water mains in plant rooms and pipe racks.
  • Insulation checks.

Common mistakes

  • No vapour barrier.
  • Indoor still-air coefficient used outdoors in wind.

Assumptions and limits

  • Still air, steady state.
  • The water temperature rise uses the specific heat entered (4186 J/(kg·K) for water; lower for glycol and brine).

References

  • ISO 12241 insulated pipe method (engine InsulatedPipe); dew point over water or ice from IAPWS; water rise with the c_p entered

Questions and answers

DN150 at 7 °C with 40 mm insulation in 35 °C, 70 % air?

About 14.5 W/m of gain; the surface is about 4 K above the 28.7 °C dew point.

Why does a thin layer sweat?

Its surface runs too close to the pipe temperature.

Vapour barrier?

Essential: moisture in the insulation ruins it, however thick.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.