FireCADCalc

Soil Phase Relations: Void Ratio, Porosity, Saturation, Unit Weights

Void ratio, porosity, degree of saturation, air content and bulk, dry and saturated unit weights of a soil from water content, specific gravity and bulk density.

Inputs

Examples: Clayey sand, partly saturatedSaturated clayDry sand

Results

Dry density ρ/(1 + w)1,600.0kg/m³
Void ratio G_s ρ_w/ρ_d − 10.65625
Porosity e/(1 + e)39.623%
Degree of saturation w G_s/e0%
Air content n(1 − S_r)39.623%
Bulk unit weight15.691kN/m³
Saturated unit weight19.576kN/m³
Submerged unit weight9.7696kN/m³

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Clayey sand, partly saturated. The inputs, in the units selected above:

InputValue
Water content (of dry mass)18.000 %
Specific gravity of the solids2.6800 -
Bulk density1,950.0 kg/m³

Applying the formula below gives:

ResultValue
Dry density ρ/(1 + w)1,652.5 kg/m³
Void ratio G_s ρ_w/ρ_d − 10.62174
Porosity e/(1 + e)38.338 %
Degree of saturation w G_s/e77.588 %
Air content n(1 − S_r)8.5922 %
Bulk unit weight19.123 kN/m³
Saturated unit weight19.966 kN/m³
Submerged unit weight10.159 kN/m³

Open this example in the calculator and change any input.

Formula

\(\rho_d = \frac{\rho}{1 + w}, \quad e = \frac{G_s \rho_w}{\rho_d} - 1, \quad n = \frac{e}{1 + e}, \quad S_r = \frac{w G_s}{e}, \quad \gamma_{sat} = \frac{(G_s + e)\rho_w g}{1 + e}\)

Variables

Symbol Meaning SI unit
\(w\) Water content (of dry mass) -
\(G_s\) Specific gravity of the solids -
\(\rho\) Bulk density kg/m³
\(\rho_d\) Dry density ρ/(1 + w) kg/m³
\(e\) Void ratio G_s ρ_w/ρ_d − 1 -
\(n\) Porosity e/(1 + e) -
\(S_r\) Degree of saturation w G_s/e -
\(a_c\) Air content n(1 − S_r) -
\(\gamma\) Bulk unit weight N/m³
\(\gamma_{sat}\) Saturated unit weight N/m³
\(\gamma'\) Submerged unit weight N/m³

Method and standards

Phase diagram relations.

Where it is used

  • Soil investigation reports.
  • Earthwork and foundation design.

Common mistakes

  • Water content on wet mass.
  • Gs of 2.65 assumed for every soil.

Assumptions and limits

  • Water density 1000 kg/m³.

References

  • Three-phase soil relations (Das, Principles of Geotechnical Engineering; Craig, Soil Mechanics)

Questions and answers

w 18 %, Gs 2.68, bulk 1950 kg/m³?

Dry density 1653 kg/m³, void ratio 0.622, saturation 78 %.

Why is water content on dry mass?

Soil mechanics convention: the solids mass does not change.

What is the submerged unit weight for?

Effective stress below the water table.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.