FireCADCalc

Atterberg Limits: Plasticity, Liquidity and Consistency Indices

Plasticity index, liquidity index, consistency index and activity of a fine soil from its liquid limit, plastic limit, natural water content and clay fraction.

Inputs

Examples: Clay of medium plasticitySilt below the A-lineSoft clay above its liquid limit

Results

Above the A-line on the plasticity chart: clay.

Plasticity index w_L − w_P26.000%
Liquidity index (w − w_P)/I_P0.30769
Consistency index (w_L − w)/I_P0.69231
Activity I_P/clay fraction (both in %)0.74286
A-line value 0.73(w_L − 20 %)20.440%

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Clay of medium plasticity. The inputs, in the units selected above:

InputValue
Liquid limit48.000 %
Plastic limit22.000 %
Natural water content30.000 %
Clay fraction (finer than 2 µm)35.000 %

Applying the formula below gives:

ResultValue
Plasticity index w_L − w_P26.000 %
Liquidity index (w − w_P)/I_P0.30769
Consistency index (w_L − w)/I_P0.69231
Activity I_P/clay fraction (both in %)0.74286
A-line value 0.73(w_L − 20 %)20.440 %

Open this example in the calculator and change any input.

Formula

\(I_P = w_L - w_P, \quad I_L = \frac{w - w_P}{I_P}, \quad I_C = \frac{w_L - w}{I_P}, \quad A = \frac{I_P}{c}\)

Variables

Symbol Meaning SI unit
\(w_L\) Liquid limit -
\(w_P\) Plastic limit -
\(w\) Natural water content -
\(c\) Clay fraction (finer than 2 µm) -
\(I_P\) Plasticity index w_L − w_P -
\(I_L\) Liquidity index (w − w_P)/I_P -
\(I_C\) Consistency index (w_L − w)/I_P -
\(A\) Activity I_P/clay fraction (both in %) -
\(I_{P,A}\) A-line value 0.73(w_L − 20 %) -

Method and standards

Definitions.

Where it is used

  • Soil classification.
  • Foundation and earthwork suitability.

Common mistakes

  • Mixing percent and fraction.
  • Non-plastic soils.

Assumptions and limits

  • Fine soils. The note is a simple A-line check; ASTM D2487 also has the CL-ML band (PI 4–7) and needs PI of at least 7 above the A-line for CL, so low-PI soils are flagged rather than called clay.

References

  • Atterberg limit indices; Casagrande A-line I_P = 0.73(w_L − 20) (ASTM D2487)

Questions and answers

LL 48 %, PL 22 %, w 30 %?

PI 26 %, liquidity index 0.31, consistency index 0.69; above the A-line, a clay.

What does liquidity index tell?

Near 0 the soil is stiff, near 1 it is close to liquid.

Activity?

High activity (> 1.25) means swelling clay minerals.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.