FireCADCalc

Slope Stability: Culmann Critical Height and Taylor's Stability Number

Critical height of a slope by Culmann's plane-failure method, and the factor of safety on cohesion using Taylor's stability number from the chart.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationRefinery and petrochemicalChemical and fertiliserPulp and paper

Inputs

Examples: 8 m cut at 45°, c 25 kPa, φ 10°Clay slope 30°, c 30 kPa, φ 0

Results

Culmann assumes a plane through the toe and over-estimates critical height for flatter slopes; Taylor's circular analysis is better (read N_s for β and φ from Taylor's chart). Neither includes pore pressure or layering.

Culmann critical height21.392m
Culmann height ratio H_c/H (on height, not on shear strength)2.6740
Taylor critical height11.574m
Taylor factor of safety on cohesion1.4468

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 8 m cut at 45°, c 25 kPa, φ 10°. The inputs, in the units selected above:

InputValue
Cohesion25.000 kPa
Friction angle10.000 °
Unit weight18.000 kN/m³
Slope angle45.000 °
Slope height8.0000 m
Taylor stability number from the chart0.12000 -

Applying the formula below gives:

ResultValue
Culmann critical height21.392 m
Culmann height ratio H_c/H (on height, not on shear strength)2.6740
Taylor critical height11.574 m
Taylor factor of safety on cohesion1.4468

Open this example in the calculator and change any input.

Formula

\(H_c = \frac{4c\sin\beta\cos\phi}{\gamma[1 - \cos(\beta - \phi)]}\ \text{(Culmann)}, \quad FS_{Culmann} = \frac{H_{c,Culmann}}{H}\)

\(H_{c,Taylor} = \frac{c}{\gamma N_s}, \quad FS_c = \frac{c}{N_s\gamma H}\ \text{(Taylor)}\)

Variables

Symbol Meaning SI unit
\(c\) Cohesion Pa
\(\phi\) Friction angle rad
\(\gamma\) Unit weight N/m³
\(\beta\) Slope angle rad
\(H\) Slope height m
\(N_s\) Taylor stability number from the chart -
\(H_{c,Culmann}\) Culmann critical height m
\(FS_{Culmann}\) Culmann height ratio H_c/H (on height, not on shear strength) -
\(H_{c,Taylor}\) Taylor critical height m
\(FS_c\) Taylor factor of safety on cohesion -

Method and standards

Culmann and Taylor.

Where it is used

  • Excavation and embankment checks.
  • Ash dyke and pond slopes.

Common mistakes

  • Ignoring pore water pressure.
  • Using peak strength for long-term slopes in clay.

Assumptions and limits

  • Homogeneous slope; no seepage.
  • The Culmann output is a ratio of heights, not a factor of safety on shear strength; it reads much higher than a strength-based factor for the same slope.
  • N_s is read by you from Taylor's chart for the slope angle and the friction angle; F_c is then a factor on cohesion with φ fully mobilised. For a factor on both c and φ, iterate with φ reduced by the same factor.

References

  • Culmann's plane-failure method and Taylor's (1937) stability number (Das, Principles of Geotechnical Engineering, 7th ed. (Cengage, 2010), ch. 15)

Questions and answers

What is Taylor's stability number?

N_s = c/(γH_c) for the critical circle, tabulated against slope angle and friction angle.

Why does Culmann give larger heights?

A plane is not the most critical surface; circular surfaces find weaker paths.

What do the defaults represent?

An 8 m cut at 45° in a c–φ soil with N_s = 0.12 from the chart.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.