Worked example
Example: n-Butylbenzene 333.15 K (Perry's: 0.112 W/(m K) Pachaiyappan). The inputs, in the units selected above:
| Input | Value |
|---|---|
| Temperature | 60.000 °C |
| Critical temperature | 387.35 °C |
| Molar mass | 134.22 kg/kmol |
| Hydrocarbon class (Pachaiyappan) | Branched, cyclic or aromatic |
| Molar volume at 20 °C | 162.01 cm³/mol |
| Normal boiling point (Missenard) | 183.25 °C |
| Liquid molar density at 0 °C (kmol/m³) | 6.5300 - |
| Liquid heat capacity at 0 °C (J/(mol·K)) | 225.00 - |
| Atoms in the molecule | 24.000 - |
Applying the formula below gives:
| Result | Value |
|---|---|
| Thermal conductivity, Pachaiyappan | 0.11207 W/(m·K) |
| Missenard conductivity at 0 °C | 0.12724 W/(m·K) |
| Thermal conductivity, Missenard | 0.11609 W/(m·K) |
Open this example in the calculator and change any input.
Formula
\(k = \frac{CM^m}{V_{293}}\cdot\frac{3 + 20(1 - T_r)^{2/3}}{3 + 20(1 - T_{r,293})^{2/3}}\ \ (C = 0.1811,\ m = 1.001\ \text{or}\ C = 0.4407,\ m = 0.7717)\)
\(k_{273} = \frac{8.4\,T_b^{1/2}\rho_{273}^{1/2}M^{-1/2}C_{p,273}}{n_A^{1/4}}\ \mathrm{mW/(m\,K)}\ (\rho\ \mathrm{mol/cm^3})\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(T\) | Temperature | K |
| \(T_c\) | Critical temperature | K |
| \(M\) | Molar mass | kg/kmol |
| \(\text{class}\) | Hydrocarbon class (Pachaiyappan) | - |
| \(V_{293}\) | Molar volume at 20 °C | m³/mol |
| \(T_b\) | Normal boiling point (Missenard) | K |
| \(\rho_{273}\) | Liquid molar density at 0 °C (kmol/m³) | - |
| \(C_{p,273}\) | Liquid heat capacity at 0 °C (J/(mol·K)) | - |
| \(n_A\) | Atoms in the molecule | - |
| \(k_{P}\) | Thermal conductivity, Pachaiyappan | W/(m·K) |
| \(k_{273}\) | Missenard conductivity at 0 °C | W/(m·K) |
| \(k_{M}\) | Thermal conductivity, Missenard | W/(m·K) |
Method and standards
Modified Pachaiyappan; Missenard with Perry's temperature correction.
Where it is used
- Heat exchanger design for hydrocarbons and solvents.
Common mistakes
- Using Pachaiyappan for non-hydrocarbons.
- Wrong density units (Missenard uses mol/cm³).
Assumptions and limits
- Low to moderate pressure; the liquid state is not checked, but a note appears above the normal boiling point.
- The Missenard defaults (molar density 6.36 kmol/m³, C_p 225 J/(mol·K), 24 atoms) are illustrative n-butylbenzene-like values without a particular source; the second preset uses Perry's m-xylene data. The 273 K reference in the Missenard temperature correction follows the 0 °C basis of k₂₇₃; using 273.15 K would change the result by far less than its accuracy.
References
- Perry's Chemical Engineers' Handbook
- 9th ed. (McGraw-Hill, 2019)
- sec. 2
- Eqs. (2-109)
- (2-111) and (2-112) (modified Pachaiyappan; Missenard) with the n-butylbenzene and m-xylene examples
Questions and answers
What do Perry's examples give?
n-Butylbenzene at 333.15 K: 0.112 W/(m·K) by Pachaiyappan (0.118 measured); m-xylene at 350 K: 0.123 by Missenard (0.118 in DIPPR).
Why does conductivity fall with temperature?
The liquid expands and its molecules move apart; the 3 + 20(1 − T_r)^⅔ factor captures that.
What do the Missenard defaults represent?
Illustrative n-butylbenzene data for comparison with Pachaiyappan; enter your own.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.