FireCADCalc

Jet Condenser Approach and Outlet Water

Approach of a multi-jet condenser by Hugot (eqn 40.47) from air, vacuum and water flow, the outlet water temperature and the water pressure.

Sugar mill and cogenerationIAPWS-IF97 (water and steam)Condenser and cooling tower

Inputs

Examples: Average air 15 kg/h, 66 cmHigh air 20 kg/h, 64 cm

Hugot: 10, 15 and 20 kg/h for normal minimum, average and high air.

Results

Hugot's formula is for multi-jet condensers handling up to about 2 000 m³/h; the approach grows quickly with air and with vacuum.

Approach7.8000K
Vapour temperature51.549°C
Outlet water temperature43.748°C
Water pressure needed (0.1 m per kg/h of air)1.5000m

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Average air 15 kg/h, 66 cm. The inputs, in the units selected above:

InputValue
Air to remove15.000 kg/h
Barometric pressure101.33 kPa
Vacuum66.000 cmHg
Injection water800.00 m³/h

Applying the formula below gives:

ResultValue
Approach7.8000 K
Vapour temperature51.549 °C
Outlet water temperature43.749 °C
Water pressure needed (0.1 m per kg/h of air)1.5000 m

Open this example in the calculator and change any input.

Formula

\(H_{76} = 76 - \frac{p_a - H}{1333.224\ \mathrm{Pa/cmHg}}, \quad App = 0.3(10 + R)\frac{79 - H_{76}}{76 - H_{76}}\cdot\frac{4000 - Q_1}{4000}\ [^\circ C;\ R\ \mathrm{kg/h};\ H\ \mathrm{cmHg};\ Q_1\ \mathrm{m^3/h}]\)

Variables

Symbol Meaning SI unit
\(R\) Air to remove kg/s
\(p_a\) Barometric pressure Pa
\(H\) Vacuum Pa
\(H_{76}\) Equivalent vacuum referred to a 76 cmHg barometer cmHg
\(Q_1\) Injection water m³/s
\(App\) Approach K
\(t_v\) Vapour temperature K
\(t_2\) Outlet water temperature K
\(h_w\) Water pressure needed (0.1 m per kg/h of air) m

Method and standards

Hugot's empirical formula.

Where it is used

  • Specifying multi-jet condensers.
  • Explaining poor vacuum.

Common mistakes

  • Using absolute pressure for H.
  • Leaving out air from leaks.

Assumptions and limits

  • Multi-jet condensers, normal water.
  • Hugot's vacuum is referred to a 76 cmHg barometer, so the vacuum you enter (against your barometer) is turned into the absolute pressure and then into the equivalent vacuum H₇₆ at 76 cm. At sea level the two are the same.
  • In the formula R is in kg/h, H in cmHg and Q₁ in m³/h, although the Variables table gives SI units; the page converts.
  • The injection water temperature is not an input, so the outlet temperature t₂ is not checked against it; with high air loads it can come out unrealistically low.

References

  • Hugot
  • Handbook of Cane Sugar Engineering
  • 3rd ed. (Elsevier, 1986)
  • ch. 40
  • jet condensers
  • eqn 40.47 and Table 40.21
  • pp. 897–900
  • Saturation temperature from IAPWS-IF97

Questions and answers

Why does air raise the approach?

Air blankets the water jets and slows condensation; the outgoing water cannot approach the vapour temperature as closely.

Why does the vacuum term rise near 76?

At very high vacuum there is little pressure to drive vapour into the water jets.

Water pressure?

Hugot: about 0.1 m of head per kg/h of air, and 4 m at start-up.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.