FireCADCalc

Impact Stress from a Falling Weight

Dynamic deflection, impact factor and stress when a weight falls a height onto a bar, beam or spring, from the static deflection by energy balance.

Inputs

Examples: 1 kN dropped 50 mm onto 2 000 N/mmSuddenly applied 5 kN (h = 0)200 N dropped 0.5 m onto a 50 N/mm buffer

Results

Impact factor 16.8: the dynamic stress is 16.8 times the static one; check it against the yield strength or allowable.

Energy balance with the member's mass neglected and no losses: an upper estimate. A load applied suddenly (h = 0) doubles the static values.

Static deflection W/k4.0000mm
Impact factor 1 + √(1 + 2h/δ_st)16.843
Dynamic deflection67.372mm
Dynamic stress33.686MPa
Peak dynamic force3.3686kN

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 1 kN dropped 50 mm onto 2 000 N/mm. The inputs, in the units selected above:

InputValue
Falling weight1.0000 kN
Height of fall50.000 mm
Stiffness of the member at the impact point2,000.0 N/mm
Stress under the weight applied statically10.000 MPa

Applying the formula below gives:

ResultValue
Static deflection W/k0.50000 mm
Impact factor 1 + √(1 + 2h/δ_st)15.177
Dynamic deflection7.5887 mm
Dynamic stress151.77 MPa
Peak dynamic force15.177 kN

Open this example in the calculator and change any input.

Formula

\(\delta_{st} = \frac{W}{k}, \quad n = 1 + \sqrt{1 + \frac{2h}{\delta_{st}}}, \quad \sigma_d = n\, \sigma_{st}\)

Variables

Symbol Meaning SI unit
\(W\) Falling weight N
\(h\) Height of fall m
\(k\) Stiffness of the member at the impact point N/m
\(\sigma_{st}\) Stress under the weight applied statically Pa
\(\delta_{st}\) Static deflection W/k m
\(n\) Impact factor 1 + √(1 + 2h/δ_st) -
\(\delta_d\) Dynamic deflection m
\(\sigma_d\) Dynamic stress Pa
\(F_d\) Peak dynamic force N

Method and standards

Energy balance on a linear spring.

Where it is used

  • Lifting gear and buffers.
  • Strength of materials examinations.

Common mistakes

  • Using the static stress for drops.
  • Ignoring stiff supports.

Assumptions and limits

  • Elastic member, no mass.
  • σ_st is your static stress under W (it is not computed from W); the dynamic stress is not compared with yield or an allowable, and a large impact factor is flagged.

References

  • Energy balance W(h + δ) = ½ k δ² (Timoshenko, Strength of Materials)

Questions and answers

1 kN dropped 50 mm onto a member of 2000 N/mm?

Static deflection 0.5 mm; impact factor 15.2: 15.2 times the static stress.

And a suddenly applied load?

Twice the static value.

How to soften an impact?

Lower stiffness (a buffer or spring) raises the static deflection and lowers the factor.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.