FireCADCalc

Depreciation: Straight Line and Written-Down Value

Yearly depreciation and book value of an asset by the straight-line and written-down (declining balance) methods, from cost, residual value and life.

Inputs

Examples: Boiler 10 M, residual 0.5 M, 15 years, after 5Pump set 0.8 M, 40 000, 10 years, after 3Vehicle 1.2 M, 0.2 M, 8 years, after 8

Results

Engineering-economics methods; tax and company-law depreciation follow the rates and rules set by your tax authority.

Straight-line depreciation per year76,000
Book value after year k, straight line572,000
Written-down value rate that reaches the residual value25.887%
First-year depreciation, written-down value207,092
Book value after year k, written-down value325,672

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Boiler 10 M, residual 0.5 M, 15 years, after 5. The inputs, in the units selected above:

InputValue
Cost of the asset (your currency)1.0000e+07 -
Residual (salvage) value at the end of life500,000 -
Useful life, years15.000 -
Year to report the book value after5.0000 -

Applying the formula below gives:

ResultValue
Straight-line depreciation per year633,333
Book value after year k, straight line6,833,333
Written-down value rate that reaches the residual value18.104 %
First-year depreciation, written-down value1,810,363
Book value after year k, written-down value3,684,031

Open this example in the calculator and change any input.

Formula

\(D_{SL} = \frac{C - S}{n}, \quad B_{SL} = C - k D_{SL}\)

\(r = 1 - (S/C)^{1/n}, \quad D_1 = C r, \quad B_{WDV} = C (1 - r)^k\)

Variables

Symbol Meaning SI unit
\(C\) cost currency
\(S\) residual value currency
\(n\) life years
\(k\) years elapsed years
\(D_{SL}\) straight-line depreciation per year currency
\(B_{SL}\) book value, straight line currency
\(r\) written-down rate -
\(D_1\) first-year depreciation, WDV currency
\(B_{WDV}\) book value, WDV currency

Method and standards

Straight line spreads cost less residual value evenly; the written-down value method takes a constant share of the remaining book value, with the rate that reaches the residual value at the end of the life.

Where it is used

  • Project evaluation and replacement decisions.
  • Estimating asset book values.
  • Teaching engineering economics.

Common mistakes

  • Using a zero residual value with the WDV method (it never reaches zero).
  • Mixing tax and book depreciation.
  • Forgetting part-year rules.

Assumptions and limits

  • Whole years; constant life and residual value.
  • A zero residual value is allowed for straight line; the written-down-value results are then not shown.

References

  • Straight-line and written-down-value methods

Questions and answers

How does a 10 M boiler with 0.5 M residual over 15 years depreciate?

Straight line: 0.633 M a year, book value 6.83 M after 5 years. Written-down value: 18.1 % a year, book value 3.68 M after 5 years.

Which method gives more depreciation early?

Written-down value: it takes a fixed share of a falling balance, so early years carry the most.

Are these the tax rates?

No. Tax and company-law depreciation follow the rates your tax authority sets.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.