FireCADCalc

Bar Bending: Cutting Length of a Bent Bar

Cutting length of a reinforcing bar from its straight lengths, number of bends and hooks, with deductions for bends and lengths for hooks as set by your standard.

Inputs

Examples: Bent-up bar 16 mmStirrup 8 mm, 3 bends and 2 hooksStraight bar with hooks 12 mm

Your code or detailing standard; commonly 1 d.
Commonly 2 d.
Commonly 9 d for a 180° hook.

Results

Deductions and hook lengths follow your detailing standard; the defaults are common site values.

Cutting length of one bar1.5120m
Total length302.40m
Total mass (steel 7850 kg/m³)119.32kg

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Bent-up bar 16 mm. The inputs, in the units selected above:

InputValue
Sum of the straight lengths (outside dimensions)4.8000 m
Bar diameter16.000 mm
Number of 45° bends2.0000 -
Number of 90° bends2.0000 -
Number of hooks0 -
Deduction per 45° bend (× d)1.0000 -
Deduction per 90° bend (× d)2.0000 -
Length per hook (× d)9.0000 -
Number of bars20.000 -

Applying the formula below gives:

ResultValue
Cutting length of one bar4.7040 m
Total length94.080 m
Total mass (steel 7850 kg/m³)148.49 kg

Open this example in the calculator and change any input.

Formula

\(L_c = \Sigma L - (n_{45} k_{45} + n_{90} k_{90}) d + n_h k_h d, \quad L_t = n L_c, \quad m = 7850\ \mathrm{kg/m^3} \cdot L_t\,\frac{\pi d^2}{4}\)

Variables

Symbol Meaning SI unit
\(\Sigma L\) Sum of the straight lengths (outside dimensions) m
\(d\) Bar diameter m
\(n_{45}\) Number of 45° bends -
\(n_{90}\) Number of 90° bends -
\(n_h\) Number of hooks -
\(k_{45}\) Deduction per 45° bend (× d) -
\(k_{90}\) Deduction per 90° bend (× d) -
\(k_h\) Length per hook (× d) -
\(n\) Number of bars -
\(L_c\) Cutting length of one bar m
\(L_t\) Total length m
\(m\) Total mass (steel 7850 kg/m³) kg

Method and standards

Bar bending schedule rule.

Where it is used

  • Bar bending schedules.
  • Steel ordering.

Common mistakes

  • Adding instead of deducting at bends.
  • Hooks forgotten.

Assumptions and limits

  • Values from the detailing standard; the defaults (1 d, 2 d, 9 d) are common site rules that depend on bend radius and code.
  • There is no separate 135° bend (stirrup hook) input: fold its allowance into the hook length k_h.
  • Steel density 7 850 kg/m³.

References

  • Cutting length = straight lengths − bend deductions + hooks (bar bending schedule practice)

Questions and answers

4.8 m of outside dimensions, 16 mm bar, two 45° and two 90° bends?

4.704 m cutting length.

Why deduct at bends?

Outside dimensions overstate the bar along the inside of the bend.

Which values?

Your standard's: they depend on bend radius.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.