FireCADCalc

Grinding Ball Size by Bond's Formula

Make-up ball size (and rod size) for a ball mill from feed size, work index, feed specific gravity, percent critical speed and mill diameter by Bond's formula.

Inputs

Examples: Duda Table 5.11.1 first row: 500 µm, Wi 12 kWh/sh tCement clinker finish mill, dryCopper ore primary ball mill, wet

Results

Bond's formula gives the largest (make-up) ball; select the nearest commercial size, a little larger below 1 inch. The work index is converted to Bond's short-ton basis. Rod size by the 1.23 ratio quoted in Perry's.

Make-up ball diameter15.842mm
Equivalent make-up rod diameter19.486mm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Duda Table 5.11.1 first row: 500 µm, Wi 12 kWh/sh t. The inputs, in the units selected above:

InputValue
Feed 80 % passing size500.00 µm
Bond work index (metric tonne)13.228 kWh/t
Specific gravity of the feed2.7000 g/cm³
Mill speed as a fraction of critical76.000 %
Mill diameter inside the liners9.0000 ft
GrindingWet grinding (K = 350)

Applying the formula below gives:

ResultValue
Make-up ball diameter15.842 mm
Equivalent make-up rod diameter19.486 mm

Open this example in the calculator and change any input.

Formula

\(B = \sqrt{\frac{F}{K}}\sqrt[3]{\frac{W_i S}{C_s\sqrt{D}}}\ \ (\text{in; }F\ \mu m,\ W_i\ \text{kWh/sh t},\ C_s\ \%,\ D\ \text{ft})\)

Variables

Symbol Meaning SI unit
\(F\) Feed 80 % passing size m
\(W_i\) Bond work index (metric tonne) J/kg
\(S\) Specific gravity of the feed kg/m³
\(C_s\) Mill speed as a fraction of critical -
\(D\) Mill diameter inside the liners m
\(K\) Grinding -
\(B\) Make-up ball diameter m
\(1.23B\) Equivalent make-up rod diameter m

Method and standards

Bond's ball size formula.

Where it is used

  • Selecting make-up ball size for cement and mineral mills.
  • Charging a new mill.

Common mistakes

  • Using the metric work index without conversion.
  • Entering speed in rpm instead of percent critical.

Assumptions and limits

  • Production-size mills.

References

  • Duda
  • Cement Data Book
  • Vol. 1
  • 3rd ed. (Bauverlag / Macdonald and Evans, 1985)
  • sec. 5.11 (Bond's ball size formula) and Table 5.11.1
  • Perry's Chemical Engineers' Handbook
  • 9th ed.
  • sec. 21 (rod to ball size ratio 1.23)

Questions and answers

Why does a coarser feed need larger balls?

Each ball must carry enough impact energy to break the largest particles; ball mass grows with the cube of its diameter.

Is it valid for laboratory mills?

No: Perry's notes the formula gives reasonable results for production mills but not for small laboratory mills.

What do the defaults represent?

The first row of Duda's Table 5.11.1: feed 500 µm, Wi 12 kWh per short ton, S 2.7, 76 % of critical, 9 ft mill (0.625 in).

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.