FireCADCalc

Rotary Kiln Drive Power (Friction and Load)

Drive power of a rotary kiln as roller-bearing friction plus load power, with sin θ found from the degree of filling, by Duda's formulas.

Inputs

Examples: Duda's example: 13 ft 6 in x 190 ft preheater kiln, 1,600,000 lb4.8 x 72 m kiln, 3.5 rpmLime kiln, grease bearings

Results

Duda reads sin θ from a chart against filling; here it is the sine of half the bed's central angle, which reproduces the chart (0.77 at 12 %). Add drive losses and a start-up margin; Duda's ratio for preheater kilns is about 4.5–4.8 m³ of kiln volume per kW.

sin θ from the filling0.76425
Friction power22.265kW
Load power124.27kW
Total drive power146.54kW

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Duda's example: 13 ft 6 in x 190 ft preheater kiln, 1,600,000 lb. The inputs, in the units selected above:

InputValue
Total vertical load on all roller shaft bearings725.75 t
Roller shaft bearing diameter406.40 mm
Riding ring (tyre) diameter4,419.6 mm
Support roller diameter1,066.8 mm
Kiln speed1.7000 rpm
Roller bearingsOil-lubricated (F = 0.018)
Kiln diameter inside the lining3.5052 m
Degree of filling12.000 %
Kiln length57.912 m
MaterialCement, wet or dry (35° repose)

Applying the formula below gives:

ResultValue
sin θ from the filling0.76425
Friction power22.265 kW
Load power124.27 kW
Total drive power146.54 kW

Open this example in the calculator and change any input.

Formula

\(HP_f = \frac{W\,b_d\,t_d\,N\,F\,0.0000092}{r_d}, \quad HP_l = (D\sin\Theta)^3 N L K, \quad \frac{2\Theta - \sin2\Theta}{2\pi} = f\)

Variables

Symbol Meaning SI unit
\(W\) Total vertical load on all roller shaft bearings kg
\(b_d\) Roller shaft bearing diameter m
\(t_d\) Riding ring (tyre) diameter m
\(r_d\) Support roller diameter m
\(N\) Kiln speed 1/s
\(F\) Roller bearings -
\(D\) Kiln diameter inside the lining m
\(f\) Degree of filling -
\(L\) Kiln length m
\(K\) Material -
\(\sin\Theta\) sin θ from the filling -
\(P_f\) Friction power W
\(P_l\) Load power W
\(P\) Total drive power W

Method and standards

Friction and load horsepower.

Where it is used

  • Selecting kiln drives.
  • Checking drives for a speed increase.

Common mistakes

  • Using the shell diameter for D.
  • Forgetting multi-diameter kilns need each section separately.

Assumptions and limits

  • Imperial formula; uniform bed.

References

  • Duda
  • Cement Data Book
  • Vol. 1
  • 3rd ed. (Bauverlag / Macdonald and Evans, 1985)
  • sec. 19.1.6 and its worked example

Questions and answers

Why two terms?

One overcomes friction in the support-roller bearings, the other lifts the off-centre bed as the kiln turns.

How good is the estimate?

Duda's example gives 200 HP for a 13′6″ × 190 ft preheater kiln, which is what such kilns were fitted with (150 kW).

What do the defaults represent?

Duda's example: 1,600,000 lb on the rollers, 16 in roller shafts, 174 in tyres, 42 in rollers, 1.7 rpm, 11.5 ft inside lining, 12 % filling, 190 ft.

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.