FireCADCalc

Grinding Media Charge: Filling Degree and Ball Mass

Filling degree of a ball mill from the measured free height, and the volume and mass of grinding media in a compartment from its size, filling and bulk density.

Inputs

Examples: Duda's compartment I: 2.5 m x 3.5 m, 30 % fillingFree height 2.6 m in a 4.2 m millCylpebs compartment, 3.65 m mill

Results

Duda's recommended filling for a three-compartment mill: 30 %, 27 % and 24 % by volume with 100–60, 60–35 and 30–20 mm media. The bulk density of balls varies little with size.

Filling degree30.000%
Compartment volume17.181m³
Bulk volume of media5.1542m³
Media mass23.451t

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Duda's compartment I: 2.5 m x 3.5 m, 30 % filling. The inputs, in the units selected above:

InputValue
Mill diameter inside the liners2.5000 m
Compartment length3.5000 m
Filling fromFilling degree entered
Filling degree (charge volume / mill volume)30.000 %
Free height (charge surface to top of the liner)1.6000 m
Bulk density of the media (balls 4.55, Cylpebs 4.85 t/m³)4.5500 g/cm³

Applying the formula below gives:

ResultValue
Filling degree30.000 %
Compartment volume17.181 m³
Bulk volume of media5.1542 m³
Media mass23.451 t

Open this example in the calculator and change any input.

Formula

\(\phi = \frac{\theta - \sin\theta}{2\pi}, \quad \cos\frac{\theta}{2} = \frac{D/2 - (D - H)}{D/2}, \quad M = \frac{\pi D^2}{4}L\,\phi\,\rho_b\)

Variables

Symbol Meaning SI unit
\(D\) Mill diameter inside the liners m
\(L\) Compartment length m
\(\text{input}\) Filling from -
\(\phi\) Filling degree (charge volume / mill volume) -
\(H\) Free height (charge surface to top of the liner) m
\(\rho_b\) Bulk density of the media (balls 4.55, Cylpebs 4.85 t/m³) kg/m³
\(V\) Compartment volume m³
\(V_b\) Bulk volume of media m³
\(M\) Media mass kg

Method and standards

Circular segment and bulk mass.

Where it is used

  • Topping up ball charges.
  • Checking charge against motor power.

Common mistakes

  • Using the shell instead of the inside-liner diameter.
  • Using solid steel density instead of bulk density.

Assumptions and limits

  • Level charge surface at rest.

References

  • Duda
  • Cement Data Book
  • Vol. 1
  • 3rd ed. (Bauverlag / Macdonald and Evans, 1985)
  • secs. 5.7-5.10 (grinding ball charge, hints for mill charging)

Questions and answers

How is the free height measured?

With the mill stopped, from the surface of the charge vertically up to the liner at the top of the mill.

What filling is normal?

About 25–35 % in cement mills; power draw peaks near 45 %, but media cost and wear favour less.

What do the defaults represent?

Duda's compartment I: a 2.5 m diameter by 3.5 m compartment filled 30 % with balls of 4.55 t/m³ bulk (about 23 t).

Method and article reviewed by FireCAD engineering on 17 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.