Worked example
Example: Skid: motor, pump, panel. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Mass 1 | 1,200.0 kg |
| x of 1 | 0.50000 m |
| y of 1 | 0.80000 m |
| z of 1 | 0 m |
| Mass 2 | 800.00 kg |
| x of 2 | 2.0000 m |
| y of 2 | 0.50000 m |
| z of 2 | 0 m |
| Mass 3 | 400.00 kg |
| x of 3 | 3.2000 m |
| y of 3 | 1.5000 m |
| z of 3 | 0.20000 m |
| Mass 4 | 0 kg |
| x of 4 | 0 m |
| y of 4 | 0 m |
| z of 4 | 0 m |
| Mass 5 | 0 kg |
| x of 5 | 0 m |
| y of 5 | 0 m |
| z of 5 | 0 m |
Applying the formula below gives:
| Result | Value |
|---|---|
| Total mass | 2,400.0 kg |
| Centre of gravity x | 1.4500 m |
| Centre of gravity y | 0.81667 m |
| Centre of gravity z | 0.033333 m |
Open this example in the calculator and change any input.
Formula
\(\bar x = \frac{\sum m_ix_i}{\sum m_i}, \quad \bar y = \frac{\sum m_iy_i}{\sum m_i}, \quad \bar z = \frac{\sum m_iz_i}{\sum m_i}\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(m_1\) | Mass 1 | kg |
| \(x_1\) | x of 1 | m |
| \(y_1\) | y of 1 | m |
| \(z_1\) | z of 1 | m |
| \(m_2\) | Mass 2 | kg |
| \(x_2\) | x of 2 | m |
| \(y_2\) | y of 2 | m |
| \(z_2\) | z of 2 | m |
| \(m_3\) | Mass 3 | kg |
| \(x_3\) | x of 3 | m |
| \(y_3\) | y of 3 | m |
| \(z_3\) | z of 3 | m |
| \(m_4\) | Mass 4 | kg |
| \(x_4\) | x of 4 | m |
| \(y_4\) | y of 4 | m |
| \(z_4\) | z of 4 | m |
| \(m_5\) | Mass 5 | kg |
| \(x_5\) | x of 5 | m |
| \(y_5\) | y of 5 | m |
| \(z_5\) | z of 5 | m |
| \(M\) | Total mass | kg |
| \(\bar x\) | Centre of gravity x | m |
| \(\bar y\) | Centre of gravity y | m |
| \(\bar z\) | Centre of gravity z | m |
Method and standards
First moments of mass.
Where it is used
- Skid and module lifting.
- Vehicle and trailer loading.
Common mistakes
- Different origins for parts.
- Forgetting fluids in tanks.
Assumptions and limits
- Point masses at part CGs.
References
- Moment of mass about axes (statics definitions)
Questions and answers
Why does CG matter in lifting?
A load hangs with its CG under the hook; slings must be arranged around it or legs carry unequal loads.
Can masses be negative?
Not here: subtract a hole by giving its mass as a separate removed part only in your own spreadsheet.
What do the defaults represent?
A skid with a 1.2 t motor, 0.8 t pump and 0.4 t panel.
Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.