FireCADCalc

Winch Drum Rope Pull by Layer and Capstan Holding Force

Winch rope pull at each drum layer from torque and layer pitch diameter, and the holding force on a capstan from friction and wrap (capstan equation).

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 20 kN·m, 400 mm drum, 20 mm rope, layer 3Small winch, layer 1

Results

Layer pitch diameter assumes rope layers stacked one rope diameter apart (simplified). Capstan equation: T_load = T_hold·e^(μφ).

Pitch diameter at the layer500.00mm
Rope pull at the layer80.000kN
Holding force on the capstan89.833N
Capstan force ratio111.32

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 20 kN·m, 400 mm drum, 20 mm rope, layer 3. The inputs, in the units selected above:

InputValue
Drum torque20,000 N·m
Bare drum diameter400.00 mm
Rope diameter20.000 mm
Layer number3.0000 -
Load-side tension on the capstan10.000 kN
Rope–capstan friction coefficient0.25000 -
Turns of wrap3.0000 -

Applying the formula below gives:

ResultValue
Pitch diameter at the layer500.00 mm
Rope pull at the layer80.000 kN
Holding force on the capstan89.833 N
Capstan force ratio111.32

Open this example in the calculator and change any input.

Formula

\(D_n = D + (2n - 1)d, \quad F_n = \frac{2M}{D_n}, \quad \frac{T_{load}}{T_{hold}} = e^{\mu\varphi}, \ \varphi = 2\pi n_w\)

Variables

Symbol Meaning SI unit
\(M\) Drum torque N·m
\(D\) Bare drum diameter m
\(d\) Rope diameter m
\(n\) Layer number -
\(T_{load}\) Load-side tension on the capstan N
\(\mu\) Rope–capstan friction coefficient -
\(n_w\) Turns of wrap -
\(D_n\) Pitch diameter at the layer m
\(F_n\) Rope pull at the layer N
\(T_{hold}\) Holding force on the capstan N
\(T_{load}/T_{hold}\) Capstan force ratio -

Method and standards

Drum statics and capstan equation.

Where it is used

  • Winch selection for pulling and hauling.
  • Mooring and capstan operations.

Common mistakes

  • Rating a winch on its bare drum pull for top layers.
  • Using dry friction for oily rope.

Assumptions and limits

  • The layer number is a whole number. The drum section (pull by layer) and the capstan section (holding force) are independent calculations on one page; the capstan inputs do not affect the drum results and vice versa.

  • Uniform friction; inextensible rope.

References

  • Capstan (Euler–Eytelwein) equation and drum statics (definitions)

Questions and answers

Why does rope pull fall on outer layers?

The same torque acts at a larger radius.

Why so much grip from a few turns?

Holding force falls exponentially with wrap: three turns at μ = 0.25 multiply the force by about 111.

What do the defaults represent?

A 20 kN·m winch with 20 mm rope on a 400 mm drum, third layer; a capstan with three turns.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.