FireCADCalc

Pneumatic Conveying: Saltation Velocity and Pressure Check (Rizk)

Minimum air velocity to avoid saltation in dilute-phase horizontal pneumatic conveying (Rizk) from loading ratio, particle size and pipe diameter.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationChemical and fertiliserPulp and paperFood, dairy and textile

Inputs

Examples: 0.5 mm, loading 5, 100 mm lineFly ash 50 µm, loading 15, 150 mm

Results

Rizk's correlation for dilute-phase horizontal flow of fairly uniform particles (about 0.1–5 mm). Use the conveying air calculator for pressure and free-air flow.

Saltation velocity12.695m/s
Design pick-up velocity15.234m/s
Air mass flow at design velocity689.15kg/h
Solids conveyed3.4457t/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 0.5 mm, loading 5, 100 mm line. The inputs, in the units selected above:

InputValue
Solids loading ratio (kg solids/kg air)5.0000 -
Particle size0.50000 mm
Pipe inside diameter100.00 mm
Safety margin on velocity20.000 %
Air density in the line1.6000 kg/m³

Applying the formula below gives:

ResultValue
Saltation velocity12.695 m/s
Design pick-up velocity15.234 m/s
Air mass flow at design velocity689.15 kg/h
Solids conveyed3.4457 t/h

Open this example in the calculator and change any input.

Formula

\(\mu_s = \frac{1}{10^\delta}Fr^\chi, \quad Fr = \frac{v_s}{\sqrt{gD}}, \quad \delta = 1.44d_p + 1.96, \ \chi = 1.1d_p + 2.5\ (d_p\ \mathrm{mm})\)

Variables

Symbol Meaning SI unit
\(\mu_s\) Solids loading ratio (kg solids/kg air) -
\(d_p\) Particle size m
\(D\) Pipe inside diameter m
\(m\) Safety margin on velocity -
\(\rho_a\) Air density in the line kg/m³
\(v_s\) Saltation velocity m/s
\(v_d\) Design pick-up velocity m/s
\(\dot m_a\) Air mass flow at design velocity kg/s
\(\dot m_s\) Solids conveyed kg/s

Method and standards

Rizk correlation.

Where it is used

  • Fly ash and cement conveying lines.
  • Biomass and grain conveying.

Common mistakes

  • Using the outlet velocity as the pick-up velocity.
  • Applying it to dense-phase systems.

Assumptions and limits

  • Dilute phase; horizontal.
  • Particles of about 0.1–5 mm; outside that range a warning is given and the result is a rough estimate only.

References

  • Rizk (1973) saltation correlation μ_s = 10^−δ Fr^χ
  • δ = 1.44d_p + 1.96
  • χ = 1.1d_p + 2.5 (d_p in mm)
  • as given in Klinzing et al.
  • Pneumatic Conveying of Solids (2010)

Questions and answers

What is saltation?

Below a certain air velocity, particles drop out and form a moving bed on the bottom of a horizontal pipe; pressure drop then rises and the line can block.

Why add a margin?

Velocity is lowest at the pick-up point, where pressure is highest; designers add 20–50 % there.

What do the defaults represent?

0.5 mm particles at a loading ratio of 5 in a 100 mm line.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.