Worked example
Example: Coal bunker 4 m dia, 6 m straight, 60° hopper to 300 mm, 800 kg/m³. The inputs, in the units selected above:
| Input | Value |
|---|---|
| Silo diameter | 4.0000 m |
| Height of the cylindrical part | 6.0000 m |
| Hopper outlet diameter | 300.00 mm |
| Hopper wall angle from horizontal | 60.000 ° |
| Angle of repose of the heaped top (0 = level) | 0 ° |
| Bulk density of the material | 800.00 kg/m³ |
Applying the formula below gives:
| Result | Value |
|---|---|
| Height of the hopper cone | 3.2043 m |
| Volume of the hopper | 14.504 m³ |
| Volume of the cylindrical part | 75.398 m³ |
| Volume of the heaped top | 0 m³ |
| Total volume | 89.902 m³ |
| Capacity at the bulk density | 71.922 t |
Open this example in the calculator and change any input.
Formula
\(h_c = \frac{D - d}{2} \tan\theta, \quad V_c = \frac{\pi h_c}{12} (D^2 + D d + d^2)\)
\(V_s = \frac{\pi}{4} D^2 H, \quad V_t = \frac{\pi D^2}{12} \cdot \frac{D}{2} \tan\phi\)
\(V = V_c + V_s + V_t, \quad W = V \rho_b\)
Variables
| Symbol | Meaning | SI unit |
|---|---|---|
| \(D\) | silo diameter | m |
| \(H\) | height of the cylinder | m |
| \(d\) | outlet diameter | m |
| \(\theta\) | hopper wall angle from horizontal | rad |
| \(\phi\) | angle of repose of the heaped top | rad |
| \(\rho_b\) | bulk density | kg/m³ |
| \(h_c\) | hopper height | m |
| \(V_c\) | hopper volume | m³ |
| \(V_s\) | cylinder volume | m³ |
| \(V_t\) | heaped top volume | m³ |
| \(V\) | total volume | m³ |
| \(W\) | capacity | kg |
Method and standards
The hopper is a frustum of a cone from the silo diameter to the outlet; the heaped top is a cone at the angle of repose. Capacity is total volume times bulk density.
Where it is used
- Sizing coal, ash, limestone and biomass silos.
- Converting a level reading to stored tonnes.
- Comparing bunker designs.
Common mistakes
- Using particle density instead of bulk density.
- Taking the hopper angle from vertical instead of horizontal.
- Counting volume above the inlet that never fills.
Assumptions and limits
- Round silo with a single central conical outlet.
- Geometric volume; hang-ups and dead zones reduce live capacity.
References
- Geometry of cylinder
- frustum and cone
Questions and answers
How much does a 4 m silo with 6 m straight and a 60° hopper hold?
About 90 m³: 75 m³ in the cylinder and 14.5 m³ in the hopper, about 72 t of coal at 800 kg/m³.
What hopper angle should I use?
Steep enough for mass flow of the material; 60° or steeper from horizontal is common for coal and ash, but cohesive materials need a flow test.
Is the heaped top usable?
Only if the filling point is central and the roof allows it; take 0 for a level fill.
Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.