FireCADCalc

Shaft Critical Speed (Simply Supported, with a Disc)

First critical speed of a simply supported solid round shaft from its own mass and a central disc, by the exact uniform-beam result and Dunkerley's combination.

Thermal power plantProcess steam and utilities

Inputs

Examples: 50 mm steel shaft, 1.2 m span, 25 kg disc80 mm, 2 m, 150 kg fan wheel30 mm, 0.8 m, no disc

Results

Dunkerley gives a lower bound. Stiff-bearing assumption: flexible bearings and supports lower the critical speed further. Keep running speed well away from it.

Critical speed of the shaft alone4,129.5rpm
Critical speed of the disc on a massless shaft2,493.4rpm
Combined critical speed (Dunkerley)2,134.5rpm

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 mm steel shaft, 1.2 m span, 25 kg disc. The inputs, in the units selected above:

InputValue
Span between bearings1.2000 m
Shaft diameter50.000 mm
Young's modulus200.00 GPa
Shaft density7,850.0 kg/m³
Mass of a disc at mid-span25.000 kg

Applying the formula below gives:

ResultValue
Critical speed of the shaft alone4,129.5 rpm
Critical speed of the disc on a massless shaft2,493.4 rpm
Combined critical speed (Dunkerley)2,134.5 rpm

Open this example in the calculator and change any input.

Formula

\(\omega_s = \frac{\pi^2}{L^2}\sqrt{\frac{EI}{\rho A}}, \quad \omega_d = \sqrt{\frac{48 E I}{m L^3}}, \quad \frac{1}{\omega_c^2} = \frac{1}{\omega_s^2} + \frac{1}{\omega_d^2}, \quad N = \frac{\omega}{2\pi}, \quad I = \frac{\pi d^4}{64}, \quad A = \frac{\pi d^2}{4}\)

Variables

Symbol Meaning SI unit
\(L\) Span between bearings m
\(d\) Shaft diameter m
\(E\) Young's modulus Pa
\(\rho\) Shaft density kg/m³
\(m\) Mass of a disc at mid-span kg
\(N_s\) Critical speed of the shaft alone 1/s
\(N_d\) Critical speed of the disc on a massless shaft 1/s
\(N_c\) Combined critical speed (Dunkerley) 1/s
\(I\) Second moment of area of the shaft m⁴
\(A\) Cross-section area of the shaft m²
\(\omega_s, \omega_d, \omega_c\) Angular critical speeds (shaft, disc, combined) rad/s

Method and standards

Beam vibration and Dunkerley's rule.

Where it is used

  • Fans, pumps and long shafts.
  • Machine design examinations.

Common mistakes

  • Ignoring bearing flexibility.
  • Running close to the critical speed.

Assumptions and limits

  • Simply supported, uniform, solid round shaft of any material (E and ρ are inputs); hollow shafts are not covered.
  • The disc is a point mass at mid-span; its gyroscopic effect and the flexibility of bearings and supports are ignored (both change the real critical speed, flexible supports lower it).
  • With no disc, N_d is not applicable and is not shown.

References

  • Euler–Bernoulli beam: ω = (π/L)² √(EI/ρA) for a simply supported shaft; Dunkerley (1894)

Questions and answers

A 50 mm steel shaft spanning 1.2 m with a 25 kg disc at mid-span?

Shaft alone about 4130 rpm; disc alone about 2490 rpm; combined about 2130 rpm.

What margin is usual?

Run at least 20 to 25 % away from a critical speed.

Why is Dunkerley a lower bound?

Adding the reciprocal squares slightly under-states the combined frequency.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.