FireCADCalc

Kv to Cv Conversion and Valve Flow

Converts a valve flow coefficient between Kv (m³/h at 1 bar) and Cv (US gpm at 1 psi), and gives the liquid flow through the valve at a pressure drop.

Thermal power plantProcess steam and utilitiesRefinery and petrochemicalChemical and fertiliserPump

Inputs

Examples: Kv 100 at 1 bar, waterCv 50 at 2.5 bar, SG 0.85Kv 6.3 at 0.4 bar, brine SG 1.2

Results

Non-choked, non-flashing liquid flow; for sizing with choked flow or gases use the IEC 60534 control valve calculators.

Kv6.3000
Cv7.2834
Liquid flow at the pressure drop3.6373m³/h

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: Kv 100 at 1 bar, water. The inputs, in the units selected above:

InputValue
Coefficient knownKv
Value of the known coefficient100.00 -
Pressure drop across the valve1.0000 bar
Specific gravity of the liquid (water = 1)1.0000 -

Applying the formula below gives:

ResultValue
Kv100.00
Cv115.61
Liquid flow at the pressure drop100.00 m³/h

Open this example in the calculator and change any input.

Formula

\(K_v = 0.865\, C_v\)

\(Q = K_v \sqrt{\frac{\Delta p / 1\,\text{bar}}{SG}} \ \text{m}^3/\text{h}\)

Variables

Symbol Meaning SI unit
\(\text{known}\) which coefficient is known -
\(K\) value of the known coefficient -
\(\Delta p\) pressure drop Pa
\(SG\) specific gravity -
\(K_v\) Kv: m³/h at 1 bar drop -
\(C_v\) Cv: US gpm at 1 psi drop -
\(Q\) liquid flow m³/s

Method and standards

Kv is the flow of water in m³/h at a 1 bar drop; Cv is US gallons per minute at a 1 psi drop. The ratio follows from the exact unit definitions: Kv = Cv × 0.2271 m³/h per gpm × √(14.504 psi per bar) = 0.865 Cv (flow rises with the square root of the pressure drop, from 1 psi to 1 bar).

Where it is used

  • Comparing valves from European and American makers.
  • Checking flow through a manual or control valve.
  • Converting data-sheet coefficients.

Common mistakes

  • Using Kv where the formula expects Cv.
  • Forgetting the square root on pressure drop.
  • Applying liquid formulas to gas or steam.

Assumptions and limits

  • Turbulent, non-choked liquid flow.

References

  • Definitions of Kv and Cv

Questions and answers

How do I convert Kv to Cv?

Cv = 1.156 Kv, and Kv = 0.865 Cv. A Kv 100 valve is Cv 115.6.

How much water passes a Kv 100 valve at 1 bar?

100 m³/h by definition; at 4 bar twice as much, since flow rises with the square root of the drop.

Is this enough to size a control valve?

For clean liquids without choking, as a check; use the IEC 60534 calculators for flashing, cavitating or gas service.

Method and article reviewed by FireCAD engineering on 12 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.