FireCADCalc

Control Valve Actuator Thrust and Spring Check

Thrust to close a globe valve against shut-off pressure, packing friction and seat load, and the spring thrust a diaphragm actuator gives at bench set.

Thermal power plantProcess steam and utilitiesSugar mill and cogenerationDistillery and ethanolRefinery and petrochemicalChemical and fertiliser

Inputs

Examples: 50 mm seat, 10 bar, 645 cm², 1.0 bar80 mm seat, 6 bar, 1,000 cm², 0.8 bar

Results

Unbalanced single-seat plug, flow tending to open. Spring-to-close actuators seat with the spring force at the lower bench-set pressure. Seat load sets the leakage class: larger loads for tighter shut-off (take values from the valve maker). Stem area and flow-to-close effects are not modelled.

Unbalance (fluid) force1,963.5N
Seat load3,141.6N
Required thrust5,505.1N
Available spring thrust at seating6,450.0N
Thrust margin1.1716

Download PDF CSV Link to this result Compare another case

Log in to save calculations to your dashboard.

Worked example

Example: 50 mm seat, 10 bar, 645 cm², 1.0 bar. The inputs, in the units selected above:

InputValue
Shut-off pressure drop10.000 bar
Seat (port) diameter50.000 mm
Packing friction400.00 N
Seat load per mm of seat circumference (N/mm)20.000 -
Effective diaphragm area645.00 cm²
Bench-set pressure at the seating end1.0000 bar

Applying the formula below gives:

ResultValue
Unbalance (fluid) force1,963.5 N
Seat load3,141.6 N
Required thrust5,505.1 N
Available spring thrust at seating6,450.0 N
Thrust margin1.1716

Open this example in the calculator and change any input.

Formula

\(F_{req} = \Delta p_{so}\frac{\pi d_s^2}{4} + F_p + f_s\pi d_s, \quad F_{av} = p_bA_d\)

Variables

Symbol Meaning SI unit
\(\Delta p_{so}\) Shut-off pressure drop Pa
\(d_s\) Seat (port) diameter m
\(F_p\) Packing friction N
\(f_s\) Seat load per mm of seat circumference (N/mm) -
\(A_d\) Effective diaphragm area m²
\(p_b\) Bench-set pressure at the seating end Pa
\(F_{unb}\) Unbalance (fluid) force N
\(F_{seat}\) Seat load N
\(F_{req}\) Required thrust N
\(F_{av}\) Available spring thrust at seating N
\(F_{av}/F_{req}\) Thrust margin -

Method and standards

Force balance.

Where it is used

  • Actuator selection.
  • Troubleshooting seat leakage.

Common mistakes

  • Ignoring packing friction (graphite packing is high).
  • Using supply instead of bench pressure.

Assumptions and limits

  • The page warns when the thrust margin is below 1 (the actuator cannot seat the plug).

  • Flow tending to open the plug is assumed; the stem area (which adds p₁ × stem area against closing) and flow-to-close arrangements (where the fluid helps closure but can slam the plug) are not modelled.

  • Unbalanced plug; spring-to-close.

References

  • Force balance on an unbalanced globe valve plug and a spring–diaphragm actuator (Lipták, Instrument Engineers' Handbook, 4th ed. (CRC Press), vol. 2, control valve actuators)

Questions and answers

Why does the valve leak at shut-off?

Often because the actuator cannot push the plug hard enough against the full shut-off pressure plus friction.

What is bench set?

The air pressure range over which the actuator strokes on the bench with no process pressure; the seating end sets the spring force at closure.

What do the defaults represent?

A 50 mm seat closing against 10 bar with a 645 cm² diaphragm and 1.0 bar bench set at the seat.

Method and article reviewed by FireCAD engineering on 13 November 2026. Every result is checked against an independent calculation on each release: how we verify our calculators.

Related calculators

Free engineering calculators: every page computes in SI and converts to your units. Results are for engineering estimation; verify critical designs against the referenced standards.

Rejoining the server...

Rejoin failed... trying again in seconds.

Failed to rejoin.
Please retry or reload the page.

The session has been paused by the server.

Failed to resume the session.
Please retry or reload the page.